{"id":10905,"date":"2026-11-21T04:46:43","date_gmt":"2026-11-21T04:46:43","guid":{"rendered":"https:\/\/premiumalu.com\/?p=10905"},"modified":"2026-11-21T04:46:43","modified_gmt":"2026-11-21T04:46:43","slug":"8009-aluminum-guide-parts-run-hot","status":"publish","type":"post","link":"https:\/\/premiumalu.com\/de\/8009-aluminum-guide-parts-run-hot\/","title":{"rendered":"8009 Aluminium: Ein Leitfaden f\u00fcr Bauteile, die hei\u00df laufen"},"content":{"rendered":"<h2 class=\"wp-block-heading\">Was ist 8009-Aluminium?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">8009-Aluminium geh\u00f6rt zu den 8xxx-G\u00fcten \u2014 der Serie, die Eisen statt Kupfer, Magnesium oder Zink als Hauptzusatz enth\u00e4lt \u2014 und es existiert f\u00fcr eine Aufgabe: Bauteile, die unter Hitze Last tragen m\u00fcssen, \u00fcblicherweise zwischen 150 \u00b0C und 300 \u00b0C. Das ist der Bereich, in dem 6061 und 2024 bereits den Gro\u00dfteil der Festigkeit verloren haben, die ihnen die W\u00e4rmebehandlung verliehen hat.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Seine Festigkeit stammt \u00fcberhaupt nicht aus einer W\u00e4rmebehandlung. Sie kommt von einer sehr gro\u00dfen Anzahl feiner Partikel \u2014 Eisen, Silizium und Vanadium, die w\u00e4hrend der Herstellung in das Metall eingemischt werden. Das ist der gesamte Unterschied zwischen 8009 und den Legierungen, die die meisten K\u00e4ufer kennen. Das Metall wird aus Pulver hergestellt, das extrem schnell abgek\u00fchlt wird, anstatt auf die \u00fcbliche Weise zu einem massiven Block gegossen zu werden, und diese schnelle Abk\u00fchlung ist es, die die Partikel fein genug h\u00e4lt, um ihre Aufgabe zu erf\u00fcllen.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Die Kosten dieses Vorteils liegen auf der Beschaffungsseite, nicht auf der Konstruktionsseite. Nur sehr wenige Werke k\u00f6nnen das Pulver herstellen, daher ist das Material kein Katalogartikel. Es wird in zwei Zust\u00e4nden geliefert statt in einer Stufenleiter von Aush\u00e4rtungszust\u00e4nden. Und die f\u00fcr das Material verfasste Luftfahrt-Spezifikation deckt nur Blech ab, was bedeutet, dass alles Dickere oder in anderer Form gegen eine Zeichnung statt gegen einen Standard bestellt werden muss. Sobald die Legierung zu Ihrer Temperatur passt, bleibt nur noch die Kl\u00e4rung des Zustands, in dem sie ankommt.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Warum 8009 seine Festigkeit dort beh\u00e4lt, wo 6061 und 2024 erweichen<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">6061 und 2024 beziehen ihre Festigkeit aus der W\u00e4rmebehandlung, und eine W\u00e4rmebehandlung wird durch W\u00e4rme r\u00fcckg\u00e4ngig gemacht. Ab etwa 150 \u00b0C beginnt sich das Gef\u00fcge, das sie hart gemacht hat, allm\u00e4hlich aufzul\u00f6sen, und die Festigkeit geht mit ihm. Ein 6061-T6-Halter, der auf der Werkbank bequem innerhalb der Grenzen liegt, kann bei 200 \u00b0C stark \u00fcberlastet sein, und nichts im Datenblatt bei Raumtemperatur warnt davor.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">8009 funktioniert anders. Die Partikel, die ihm Festigkeit verleihen, sind bereits im Metall und bei Temperatur stabil: Sie wachsen nicht und l\u00f6sen sich nicht wieder im Aluminium auf. Erhitzt man das Bauteil, halten diese Partikel das Metall weiterhin davon ab, sich zu dehnen, genauso wie im kalten Zustand.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Deshalb f\u00e4llt die Festigkeit allm\u00e4hlich ab, statt abrupt einzubrechen. Wie viel davon \u00fcbrig bleibt und f\u00fcr wie lange, zeigt die folgende Tabelle.<\/p>\n\n\n\n<figure class=\"wp-block-image size-large\"><img fetchpriority=\"high\" decoding=\"async\" width=\"1200\" height=\"896\" src=\"https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/02-mechanism.webp\" alt=\"Polished metallurgical specimen mounts comparing precipitate coarsening in 6061\/2024 against stable dispersoid particles in 8009 aluminum at elevated temperatures\" class=\"wp-image-10901\" srcset=\"https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/02-mechanism.webp 1200w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/02-mechanism-300x224.webp 300w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/02-mechanism-1024x765.webp 1024w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/02-mechanism-768x573.webp 768w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/02-mechanism-16x12.webp 16w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/02-mechanism-600x448.webp 600w\" sizes=\"(max-width: 1200px) 100vw, 1200px\" \/><figcaption class=\"wp-element-caption\">Mikrostruktureller Vergleich unter Dauerhitze: Konventionelle Ausscheidungsh\u00e4rtung erweicht oberhalb von 150 \u00b0C, w\u00e4hrend die Dispersoide in 8009 bis 300 \u00b0C stabil bleiben.<\/figcaption><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">Eigenschaften von 8009-Aluminium bei Raumtemperatur und erh\u00f6hter Temperatur<\/h2>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Eigentum<\/th><th>Wert<\/th><th>Grundlage<\/th><\/tr><\/thead><tbody><tr><td>Dichte<\/td><td>2,92 g\/cm\u00b3<\/td><td>Typisch<\/td><\/tr><tr><td>Zugfestigkeit, Raumtemperatur<\/td><td>450 MPa<\/td><td>Typisch<\/td><\/tr><tr><td>Streckgrenze, Raumtemperatur<\/td><td>385 MPa<\/td><td>Typisch<\/td><\/tr><tr><td>Dehnung<\/td><td>~15%<\/td><td>Typisch<\/td><\/tr><tr><td>Zugmodul<\/td><td>90 GPa<\/td><td>Typisch<\/td><\/tr><tr><td>H\u00e4rte<\/td><td>~140 HB<\/td><td>Typisch<\/td><\/tr><tr><td>W\u00e4rmeleitf\u00e4higkeit<\/td><td>~115 W\/m\u00b7K<\/td><td>Typisch<\/td><\/tr><tr><td>W\u00e4rmeausdehnung<\/td><td>~19,0 \u00b5m\/m\u00b7\u00b0C<\/td><td>Typisch<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Bei Raumtemperatur h\u00e4lt 8009 etwa 450 MPa stand, bevor es bricht, und 385 MPa, bevor es aufh\u00f6rt, in seine Ausgangsform zur\u00fcckzukehren. Zum Vergleich: 6061-T6 \u2014 die Legierung, die die meisten Werkst\u00e4tten am besten kennen \u2014 h\u00e4lt bei denselben beiden Ma\u00dfen 310 MPa bzw. 276 MPa stand, und 7075-T6 h\u00e4lt 572 MPa bzw. 503 MPa stand. 8009 ist also kalt fester als 6061 und schw\u00e4cher als 7075, was bedeutet, dass Raumtemperatur nicht der Grund ist, es zu kaufen. Zwei andere Zahlen sind in der Praxis wichtiger. Die Dichte betr\u00e4gt 2,92 g\/cm\u00b3, etwa 8 % schwerer als 6061 wegen des Eisens, aber immer noch deutlich unter der H\u00e4lfte des Gewichts von Stahl. Eine H\u00e4rte von etwa 140 HB liegt nahe an 7075, sodass eine Werkstatt, die bereits 7075 bearbeitet, von der Zerspanbarkeit nicht \u00fcberrascht sein wird.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Die Zahlen bei Temperatur sind der Grund, warum die Legierung existiert.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Temperatur<\/th><th>Zugfestigkeit nach 1.000 h<\/th><th>Streckgrenze nach 1.000 h<\/th><\/tr><\/thead><tbody><tr><td>100 \u00b0C<\/td><td>410 MPa<\/td><td>370 MPa<\/td><\/tr><tr><td>150 \u00b0C<\/td><td>380 MPa<\/td><td>350 MPa<\/td><\/tr><tr><td>200 \u00b0C<\/td><td>350 MPa<\/td><td>310 MPa<\/td><\/tr><tr><td>250 \u00b0C<\/td><td>310 MPa<\/td><td>275 MPa<\/td><\/tr><tr><td>300 \u00b0C<\/td><td>270 MPa<\/td><td>240 MPa<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Bei 200 \u00b0C tr\u00e4gt die Legierung nach tausend Stunden bei Temperatur noch 350 MPa \u2014 etwa 78 % dessen, was sie kalt leistet. Bei 250 \u00b0C h\u00e4lt sie 310 MPa, und bei 300 \u00b0C h\u00e4lt sie noch 270 MPa, was etwas unter dem Ausgangswert von 6061-T6 bei Raumtemperatur liegt. Der Abfall von 200 \u00b0C auf 300 \u00b0C ist steiler als der Abfall von Raumtemperatur auf 200 \u00b0C, und das ist die praktische Lesart: 200\u2013300 \u00b0C ist das Arbeitsfenster, und die obere H\u00e4lfte davon erfordert mehr Sicherheitsmarge als die untere H\u00e4lfte.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Dies sind ver\u00f6ffentlichte typische Werte, nicht die Mindestwerte, die eine Spezifikation garantiert. Fordern Sie beim Lieferanten die Werte an, die f\u00fcr die W\u00e4rmebehandlung gelten, die Ihnen tats\u00e4chlich angeboten wird, und schreiben Sie die Zahl, f\u00fcr die Sie ausgelegt haben, in die Bestellung, statt sie implizit zu lassen.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Zust\u00e4nde und Produktformen \u2014 was AMS 4308 tats\u00e4chlich abdeckt<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">AMS 4308 ist die Luftfahrt-Werkstoffspezifikation f\u00fcr diese Legierung, herausgegeben von SAE International. Sie legt die Chemie, den Zustand und die Festigkeitswerte fest, die das Material erf\u00fcllen muss, und sie ist das Dokument, nach dem ein Pr\u00fcfer arbeitet, wenn das Material eintrifft. Wenn eine Zeichnung \"AMS 4308\" angibt, ist das das Versprechen des Lieferanten.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Die Chemie reduziert sich auf sechs Zeilen, und diese sind es, die auf einem Zertifikat \u00fcberpr\u00fcft werden sollten.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Element<\/th><th>Bereich (Gew.-%)<\/th><th>Was es bewirkt<\/th><\/tr><\/thead><tbody><tr><td>Eisen (Fe)<\/td><td>8.4 \u2013 8.9<\/td><td>Der Hauptzusatz; bildet die Partikel, die die Festigkeit bei Temperatur aufrechterhalten<\/td><\/tr><tr><td>Silizium (Si)<\/td><td>1.7 \u2013 1.9<\/td><td>Wirkt mit dem Eisen und dem Vanadium zusammen, um diese Partikel zu bilden<\/td><\/tr><tr><td>Vanadium (V)<\/td><td>1.1 \u2013 1.5<\/td><td>H\u00e4lt diese Partikel stabil, wenn das Bauteil hei\u00df l\u00e4uft<\/td><\/tr><tr><td>Zink (Zn)<\/td><td>0,25 max<\/td><td>Verunreinigung \u2014 dies ist die Zeile, die ein falsches Zertifikat aufdeckt<\/td><\/tr><tr><td>Sauerstoff (O)<\/td><td>0,30 max.<\/td><td>Der Fingerabdruck der Pulverroute; eine blockgegossene Legierung w\u00fcrde keine solche Grenze tragen<\/td><\/tr><tr><td>Aluminium<\/td><td>Bilanz<\/td><td>Der Rest<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Dies sind ver\u00f6ffentlichte typische Grenzwerte, konsistent mit der Chemie 8,6Fe \u2013 1,8Si \u2013 1,3V, die in AMS 4308B genannt wird. Fordern Sie die zertifizierten Werte f\u00fcr die Charge an, die Sie anbieten.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">O (gegl\u00fcht)<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">O ist der weiche Zustand. Das Metall wird absichtlich langsam erhitzt und abgek\u00fchlt, damit es umgeformt werden kann \u2014 gebogen, gewalzt oder in Form gepresst \u2014 und es gibt Festigkeit ab, um dies zu erm\u00f6glichen. Kaufen Sie O, wenn das Bauteil nach Erhalt noch geformt werden muss, und planen Sie ein, niedrigere Festigkeitswerte zu akzeptieren, bis die Umformung abgeschlossen ist.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">H112 \/ F (wie gefertigt)<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">H112 \u2014 oft als F geschrieben, f\u00fcr wie gefertigt \u2014 ist der Zustand, in dem sich das Material befindet, wenn es das Werk nach der Warmumformung verl\u00e4sst, ohne weitere Behandlung. Es ist der Standard-Konstruktionszustand und derjenige, den der Titel von AMS 4308 nennt, weil es keinen Alterungsschritt gibt, der hinzugef\u00fcgt oder \u00fcbersprungen werden k\u00f6nnte: Die Festigkeit, die die Legierung hat, ist die Festigkeit, die der Prozess erzeugt hat.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Die Formfrage ist der Punkt, an dem die meisten Bestellungen schiefgehen.<\/p>\n\n\n\n<figure class=\"wp-block-image size-large\"><img decoding=\"async\" width=\"1200\" height=\"896\" src=\"https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/04-forms-spec.webp\" alt=\"Physical product forms of 8009 aluminum comparing AMS 4308 specification sheets with custom ordered bar and heavy plate\" class=\"wp-image-10903\" srcset=\"https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/04-forms-spec.webp 1200w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/04-forms-spec-300x224.webp 300w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/04-forms-spec-1024x765.webp 1024w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/04-forms-spec-768x573.webp 768w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/04-forms-spec-16x12.webp 16w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/04-forms-spec-600x448.webp 600w\" sizes=\"(max-width: 1200px) 100vw, 1200px\" \/><figcaption class=\"wp-element-caption\">8009 product forms: AMS 4308 covers rolled sheet only; plate, bar, and custom extrusions require technical agreements on the PO.<\/figcaption><\/figure>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Formular<\/th><th>Covered by<\/th><th>What has to be on the order<\/th><\/tr><\/thead><tbody><tr><td>Sheet, 0.25\u20136.35 mm<\/td><td>AMS 4308B<\/td><td>Standard product \u2014 chemistry, state and mechanical values are fixed by the specification<\/td><\/tr><tr><td>Plate over 6.35 mm<\/td><td>No AMS coverage<\/td><td>Chemistry limits and mechanical values stated on the order<\/td><\/tr><tr><td>Stangen und Rundst\u00e4be<\/td><td>No AMS coverage<\/td><td>Chemistry limits and mechanical values stated on the order<\/td><\/tr><tr><td>Extrusion profile<\/td><td>No AMS coverage<\/td><td>Chemistry, values and section agreed per drawing<\/td><\/tr><tr><td>Rohr<\/td><td>No AMS coverage<\/td><td>Chemistry, values and dimensions agreed per drawing<\/td><\/tr><tr><td>Foil and strip below 0.25 mm<\/td><td>No AMS coverage<\/td><td>Chemistry and values stated on the order<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Only the first row has a specification standing behind it. Everything below that line is exactly as good as what the purchase order says, which is why the chemistry and the mechanical values have to be written down instead of referenced.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">One more thing to settle before the RFQ goes out: 8009 has no T6 or T8 temper. A T6 or T8 designation means the alloy is hardened by a heat treatment cycle after forming, and this alloy does not harden that way \u2014 the particles are already in it and will not re-form. If an offer names T6 or T8 for 8009, the offer is describing a different material.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Two lines on the certificate catch most of the confusion. A zinc figure of 5\u20136% describes 7075, not 8009, which carries almost no zinc. And a strength figure far above the table above usually means the numbers were carried over from another grade rather than measured on that batch.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">We buy 8009 billet, plate and bar from producers that run the powder route, then cut, machine and finish to drawing. For forms outside the AMS range, we quote against the chemistry and the properties your drawing names.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Where 8009 Is Used<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">Aerospace and Engine-Adjacent Structures<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The reason 8009 appears in aerospace work is a weight comparison, not a strength comparison. Above 150 \u00b0C the usual alternatives are titanium, steel, and the few heat-resistant aluminiums such as 2618. Titanium is about 50% heavier for the same volume and steel close to three times. A part that can stay aluminium up to 300 \u00b0C removes that penalty for anything whose service temperature lands in the band \u2014 supersonic airframe skins that heat up in flight, rocket structure, thermal-protection hardware, and brackets and housings close to an engine where the metal soaks up radiant heat without seeing combustion.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The fit is specific rather than general. If the part runs below 150 \u00b0C, 7075 or 2024 gives more strength per kilogram and is easier to buy. If it runs above 350 \u00b0C, aluminium stops competing and the titanium or steel argument takes over. 8009 earns its place in the band where neither of those answers works.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">High-Performance Automotive and Specialty Heat Exchangers<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Turbocharger and exhaust-adjacent parts see the same problem in a smaller package: cyclic heating and cooling, with load on the part the whole time. A piston or a housing that softens a little more with every heat cycle loses its clearances before it loses its shape, which is why slow stretching under load at temperature \u2014 creep \u2014 decides the material here rather than peak strength.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Specialty heat exchangers and high-temperature tooling follow the same logic from the other direction \u2014 the part is hot by design, and the question is whether the wall keeps its dimensions over a long campaign. The limiting factor for cost here is usually the size of the part rather than the material: 8009 is expensive relative to 6061, and that premium is easiest to justify on small, highly loaded components.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">8009 vs 6061, 2024, 2618 and 7075 \u2014 Choosing by Service Temperature<\/h2>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Legierung und Zustand<\/th><th>Tensile, room temp<\/th><th>Yield, room temp<\/th><th>Practical service ceiling<\/th><th>What it is for<\/th><\/tr><\/thead><tbody><tr><td>7075-T6<\/td><td>572 MPa<\/td><td>503 MPa<\/td><td>~120 \u00b0C<\/td><td>Strongest at room temperature; wrong choice for a hot part<\/td><\/tr><tr><td>2024-T3<\/td><td>483 MPa<\/td><td>345 MPa<\/td><td>~150 \u00b0C<\/td><td>Airframe skins and fatigue-critical structure<\/td><\/tr><tr><td>6061-T6<\/td><td>310 MPa<\/td><td>276 MPa<\/td><td>~150 \u00b0C<\/td><td>The default general-purpose structural alloy<\/td><\/tr><tr><td>2618-T61<\/td><td>~440 MPa<\/td><td>~370 MPa<\/td><td>~200 \u00b0C<\/td><td>Forged pistons and compressor parts<\/td><\/tr><tr><td>8009 (H112)<\/td><td>450 MPa<\/td><td>385 MPa<\/td><td>200\u2013300 \u00b0C<\/td><td>Parts that must stay aluminium while running hot<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<figure class=\"wp-block-image size-large\"><img decoding=\"async\" width=\"1200\" height=\"896\" src=\"https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/03-temp-ceiling.webp\" alt=\"Machined aluminum step block and tensile test specimens illustrating service temperature ceilings from 7075-T6 at 120 \u00b0C up to 8009 at 200\u2013300 \u00b0C\" class=\"wp-image-10902\" srcset=\"https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/03-temp-ceiling.webp 1200w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/03-temp-ceiling-300x224.webp 300w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/03-temp-ceiling-1024x765.webp 1024w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/03-temp-ceiling-768x573.webp 768w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/03-temp-ceiling-16x12.webp 16w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/03-temp-ceiling-600x448.webp 600w\" sizes=\"(max-width: 1200px) 100vw, 1200px\" \/><figcaption class=\"wp-element-caption\">Practical service temperature ceilings: 8009 uniquely fills the 200\u2013300 \u00b0C band before steel or titanium are required.<\/figcaption><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Room-temperature values above are the minimums published in ASTM B209 for sheet, except 2618, where they are typical forging values to AMS 4132. Service ceilings are practical design limits rather than values printed in any specification, and a specific duty cycle can justify going beyond them with the right testing.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Read that table by the fourth column, not the second. 7075 wins the room-temperature column and is the wrong material for a 250 \u00b0C part. 2618 is the right answer for a piston crown at 200 \u00b0C and stops being one above it. 8009 is the only grade here with a service ceiling above 200 \u00b0C.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">That is also why the two alloys are easy to compare the wrong way round. Put the datasheets side by side and 7075 shows 572 MPa against 8009&#8217;s 450 MPa, which reads like 8009 is the weaker alloy. It is weaker \u2014 at room temperature, on a bench, which is not where the part works.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Working With 8009 \u2014 Machining, Joining and Finishing<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Zerspanung:<\/strong> it cuts like a hard aluminium, not like 6061. At around 140 HB it behaves much closer to 7075, which means a shop that already runs 7075 will be comfortable and a shop that only runs 6061 should expect faster tool wear and lighter cuts. There is no free-machining version of this alloy, so how the chips break comes down to how the machine is set rather than to the metal.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>F\u00fcgen:<\/strong> welding costs you the property you bought the alloy for. A fusion weld destroys the particle structure in the weld zone, and the joint loses the high-temperature strength that justified the material in the first place. For a load-bearing joint, plan on mechanical fastening, or on a joining method that does not melt the metal and has been qualified for this alloy; treat a fusion-welded joint as non-structural unless it has been tested and accepted on its own.<\/p>\n\n\n\n<figure class=\"wp-block-image size-large\"><img loading=\"lazy\" decoding=\"async\" width=\"1200\" height=\"896\" src=\"https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/05-joining-boundary.webp\" alt=\"Comparison between recommended mechanical fastening with countersunk aerospace bolts and prohibited fusion welding showing heat-affected zone cracking on 8009 aluminum\" class=\"wp-image-10904\" srcset=\"https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/05-joining-boundary.webp 1200w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/05-joining-boundary-300x224.webp 300w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/05-joining-boundary-1024x765.webp 1024w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/05-joining-boundary-768x573.webp 768w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/05-joining-boundary-16x12.webp 16w, https:\/\/premiumalu.com\/wp-content\/uploads\/2026\/11\/05-joining-boundary-600x448.webp 600w\" sizes=\"(max-width: 1200px) 100vw, 1200px\" \/><figcaption class=\"wp-element-caption\">Joining 8009: use mechanical fastening or solid-state methods; conventional fusion welding melts the matrix and destroys dispersoid strength.<\/figcaption><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Korrosionsschutz:<\/strong> it holds up well in normal workshop and atmospheric service but it is not a marine alloy. Anodizing works, and so do chemical conversion coatings \u2014 a chemical surface treatment that leaves a protective layer on the metal. For a part that will see salt air or chemical exposure, specify the finish on the drawing rather than deciding it after the part is made.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Formung:<\/strong> shape it in O, and accept that you cannot heat-treat the strength back afterwards. This is the biggest practical difference from the 2xxx and 7xxx grades, where forming in a soft state and then aging to full strength is routine. In 8009 the H112 values are set when the material is worked hot, not by a treatment you can repeat in your own shop \u2014 so a part that needs heavy forming either starts in O and stays softer, or is formed near-final and machined from H112.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Vor- und Nachteile im \u00dcberblick<\/h2>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><thead><tr><th>Abmessung<\/th><th>Vorteil<\/th><th>Was es kostet<\/th><\/tr><\/thead><tbody><tr><td>Strength above 200 \u00b0C<\/td><td>Holds 350 MPa at 200 \u00b0C and 270 MPa at 300 \u00b0C after 1,000 hours<\/td><td>Nothing comparable in the 6xxx or 7xxx families at that temperature<\/td><\/tr><tr><td>Room-temperature strength<\/td><td>450 MPa tensile, comparable to 2618<\/td><td>Below 7075 and 2024; not a reason to choose it<\/td><\/tr><tr><td>Gewicht<\/td><td>2.92 g\/cm\u00b3 \u2014 under half of steel, so it replaces hot steel parts directly<\/td><td>About 8% heavier than 6061 for the same volume<\/td><\/tr><tr><td>Fatigue at temperature<\/td><td>160 MPa at 250 \u00b0C \u2014 published typical value \u2014 supports cyclic hot service<\/td><td>Cost per kilogram is several times 6061<\/td><\/tr><tr><td>Bearbeitung<\/td><td>Cuts predictably, close to 7075<\/td><td>~140 HB wears tooling faster than 6061<\/td><\/tr><tr><td>F\u00fcgen<\/td><td>Mechanical fastening and methods that do not melt the metal both work<\/td><td>Fusion welding removes the strength advantage locally<\/td><\/tr><tr><td>Supply<\/td><td>Available as billet, plate and bar from powder-route producers<\/td><td>Narrow producer base; lead time follows billet availability; sheet only under AMS 4308<\/td><\/tr><tr><td>Formung<\/td><td>O temper forms well<\/td><td>Formed parts cannot be re-hardened to H112<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\">Schlussfolgerung<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">8009 solves a real problem \u2014 carrying load at 200 to 300 \u00b0C without moving to titanium or steel \u2014 but nothing about it is standard. One producer tier, a specification that covers sheet only, and just two usable states mean the buying problem replaces the engineering problem as soon as the alloy is chosen.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">We buy 8009 billet, plate and bar from powder-route producers, then cut and machine to your drawing. Every order ships with an MTC, and SGS reports are available if your project needs them.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Send us the drawing with the form, state and quantity for a supply check and a cutting quote.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">H\u00e4ufig gestellte Fragen<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Can 8009 aluminum be used at 400 \u00b0C?<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">No \u2014 there is no published basis for 400 \u00b0C. Published 1,000-hour test values, rather than specification minimums, support 200\u2013300 \u00b0C; above 350 \u00b0C the particle structure needs assessment against your duty cycle.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Does 8009 have a T6 temper?<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">No. 8009 is strengthened by particles already in the metal, so there is no solution-treat-and-age step to make T6 or T8. It ships in O or H112 only, and an offer naming T6 describes another alloy.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Can you supply 8009 in bar or tube when AMS 4308 covers sheet only?<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Yes, as a drawing-controlled item. Outside the AMS thickness range there is no specification to point at, so chemistry and mechanical values travel on the purchase order, and the MTC reports what was tested.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>What is the minimum order and lead time for 8009?<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Low MOQ, typically 10\u201360 days. The date depends on billet availability and the cutting or machining you need, so it is confirmed with the quote rather than quoted in advance. Send the drawing, form, state and quantity.<\/p>","protected":false},"excerpt":{"rendered":"<p>What Is 8009 Aluminum? 8009 aluminum is one of the 8xxx grades \u2014 the series that carries iron rather than copper, magnesium or zinc as its main addition \u2014 and it exists for one job: parts that have to carry load while running hot, usually between 150 \u00b0C and 300 \u00b0C. That is the range [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":10900,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_seopress_titles_title":"8009 Aluminum: Strength That Survives Heat","_seopress_titles_desc":"What 8009 aluminum is, how much strength it keeps from 200 to 300 \u00b0C, which states and forms AMS 4308 actually covers, and how to specify it on an order.","_seopress_robots_index":"","_seopress_robots_follow":"","_seopress_robots_imageindex":"","_seopress_robots_snippet":"","_seopress_robots_primary_cat":"","_seopress_robots_breadcrumbs":"","_seopress_robots_freeze_modified_date":"","_seopress_robots_custom_modified_date":"","_seopress_robots_canonical":"","_seopress_social_fb_title":"","_seopress_social_fb_desc":"","_seopress_social_fb_img":"","_seopress_social_fb_img_attachment_id":0,"_seopress_social_fb_img_width":0,"_seopress_social_fb_img_height":0,"_seopress_social_twitter_title":"","_seopress_social_twitter_desc":"","_seopress_social_twitter_img":"","_seopress_social_twitter_img_attachment_id":0,"_seopress_social_twitter_img_width":0,"_seopress_social_twitter_img_height":0,"_seopress_redirections_value":"","_seopress_redirections_enabled":"","_seopress_redirections_enabled_regex":"","_seopress_redirections_logged_status":"","_seopress_redirections_param":"","_seopress_redirections_type":0,"_seopress_analysis_target_kw":"","footnotes":""},"categories":[186,180],"tags":[],"class_list":["post-10905","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-8000-series-aluminum","category-aluminum-alloy"],"_links":{"self":[{"href":"https:\/\/premiumalu.com\/de\/wp-json\/wp\/v2\/posts\/10905","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/premiumalu.com\/de\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/premiumalu.com\/de\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/premiumalu.com\/de\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/premiumalu.com\/de\/wp-json\/wp\/v2\/comments?post=10905"}],"version-history":[{"count":1,"href":"https:\/\/premiumalu.com\/de\/wp-json\/wp\/v2\/posts\/10905\/revisions"}],"predecessor-version":[{"id":10944,"href":"https:\/\/premiumalu.com\/de\/wp-json\/wp\/v2\/posts\/10905\/revisions\/10944"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/premiumalu.com\/de\/wp-json\/wp\/v2\/media\/10900"}],"wp:attachment":[{"href":"https:\/\/premiumalu.com\/de\/wp-json\/wp\/v2\/media?parent=10905"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/premiumalu.com\/de\/wp-json\/wp\/v2\/categories?post=10905"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/premiumalu.com\/de\/wp-json\/wp\/v2\/tags?post=10905"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}