{"id":9042,"date":"2025-09-01T01:57:46","date_gmt":"2025-09-01T01:57:46","guid":{"rendered":"https:\/\/premiumalu.com\/?post_type=product&#038;p=9042"},"modified":"2026-07-07T08:32:46","modified_gmt":"2026-07-07T08:32:46","slug":"barre-carree-en-aluminium-3003","status":"publish","type":"product","link":"https:\/\/premiumalu.com\/fr\/produit\/barre-carree-en-aluminium-3003\/","title":{"rendered":"Barre carr\u00e9e en aluminium 3003-O\/H14\/H22"},"content":{"rendered":"<h2>What Is 3003 Aluminum Square Bar?<\/h2>\n<p>3003 aluminum square bar is a bar with a square cross-section, made from 3003 Al-Mn (aluminum-manganese) alloy. As a non-heat-treatable wrought alloy, 3003 derives its strength from cold working rather than precipitation hardening. Square bar is typically produced by extrusion (in H112 or F temper) or fabricated by cutting from strain-hardened sheet or plate stock (in H14, H22, or O temper).<\/p>\n<p>With 1.0\u20131.5% manganese as its primary alloying element, 3003 offers approximately 20% higher strength than commercially pure 1100 aluminum while retaining excellent corrosion resistance, formability, and weldability. Square bar is widely specified for structural framing, machining blanks, decorative applications, tank supports, and general fabrication where a square cross-section is required for ease of fixturing, assembly, or aesthetic preference.<\/p>\n<p>Common tempers for 3003 square bar include <strong>O<\/strong> (fully annealed, maximum formability), <strong>H14<\/strong> (half hard, good balance of strength and workability), and <strong>H22<\/strong> (strain-hardened then partially annealed, stable strength with good formability). Linsy supplies 3003 square bars in these tempers with custom side dimensions, cut-to-length, surface finishing, and MTC reports available for every order.<\/p>\n<h2>Available 3003 Aluminum Square Bar \u2014 Dimensions &amp; Tempers<\/h2>\n<p>Linsy supplies 3003 aluminum square bars in standard and custom sizes. Both metric and imperial dimensions are available. Custom cut-to-length, edge conditioning (chamfered or radiused edges), and surface finishing (mill finish, anodized, or brushed) can be specified at order.<\/p>\n<h3>3003 Aluminum Square Bar \u2014 Standard Dimensions<\/h3>\n<table>\n<thead>\n<tr>\n<th>Side (mm)<\/th>\n<th>Longueur (mm)<\/th>\n<th>kg\/m (Approx.)<\/th>\n<th>Temp\u00e9raments courants<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>5 \u2013 12<\/td>\n<td>1000 \u2013 4000<\/td>\n<td>0.07 \u2013 0.39<\/td>\n<td>O, H14, H22<\/td>\n<\/tr>\n<tr>\n<td>12 \u2013 25<\/td>\n<td>1000 \u2013 5000<\/td>\n<td>0.39 \u2013 1.69<\/td>\n<td>O, H14, H112<\/td>\n<\/tr>\n<tr>\n<td>25 \u2013 50<\/td>\n<td>1000 \u2013 6000<\/td>\n<td>1.69 \u2013 6.75<\/td>\n<td>O, H22, H112, F<\/td>\n<\/tr>\n<tr>\n<td>50 \u2013 60<\/td>\n<td>1000 \u2013 6000<\/td>\n<td>6.75 \u2013 9.72<\/td>\n<td>H112, F<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><em>Note: Side dimension and length can be customized to your drawing or specification. Non-standard sizes and tighter tolerances are available on request. Contact us with your required dimensions for a quick quote.<\/em><\/p>\n<h2>Sp\u00e9cifications de l'aluminium 3003 et d\u00e9signations \u00e9quivalentes<\/h2>\n<p>3003 aluminum square bar is supplied in accordance with major international standards. If your project requires a specific standard or certificate, please specify it when requesting a quote.<\/p>\n<table>\n<thead>\n<tr>\n<th>Standard<\/th>\n<th>D\u00e9signation<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>AA (Association de l'aluminium)<\/td>\n<td>3003<\/td>\n<\/tr>\n<tr>\n<td>UNS<\/td>\n<td>A93003<\/td>\n<\/tr>\n<tr>\n<td>EN \/ DIN<\/td>\n<td>EN AW-3003 \/ AlMn1Cu<\/td>\n<\/tr>\n<tr>\n<td>ISO<\/td>\n<td>AlMn1Cu<\/td>\n<\/tr>\n<tr>\n<td>JIS H 4000<\/td>\n<td>A3003<\/td>\n<\/tr>\n<tr>\n<td>GB\/T 3190<\/td>\n<td>3003<\/td>\n<\/tr>\n<tr>\n<td>ASTM B211<\/td>\n<td>3003 bar, rod, and wire<\/td>\n<\/tr>\n<tr>\n<td>ASTM B221<\/td>\n<td>3003 extruded bar, rod, wire, profiles<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h2>Composition chimique de l'aluminium 3003<\/h2>\n<p>The following chemical composition limits apply to 3003 aluminum per ASTM B211 and EN 573-3. All values are weight percent (%).<\/p>\n<table>\n<thead>\n<tr>\n<th>\u00c9l\u00e9ment<\/th>\n<th>Min %<\/th>\n<th>Max %<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Silicium (Si)<\/td>\n<td>\u2014<\/td>\n<td>0.6<\/td>\n<\/tr>\n<tr>\n<td>Fer (Fe)<\/td>\n<td>\u2014<\/td>\n<td>0.7<\/td>\n<\/tr>\n<tr>\n<td>Cuivre (Cu)<\/td>\n<td>0.05<\/td>\n<td>0.20<\/td>\n<\/tr>\n<tr>\n<td>Mangan\u00e8se (Mn)<\/td>\n<td>1.0<\/td>\n<td>1.5<\/td>\n<\/tr>\n<tr>\n<td>Magn\u00e9sium (Mg)<\/td>\n<td>\u2014<\/td>\n<td>0.05<\/td>\n<\/tr>\n<tr>\n<td>Chrome (Cr)<\/td>\n<td>\u2014<\/td>\n<td>0.05<\/td>\n<\/tr>\n<tr>\n<td>Zinc (Zn)<\/td>\n<td>\u2014<\/td>\n<td>0.10<\/td>\n<\/tr>\n<tr>\n<td>Titane (Ti)<\/td>\n<td>\u2014<\/td>\n<td>0.05<\/td>\n<\/tr>\n<tr>\n<td>Autres Chacun<\/td>\n<td>\u2014<\/td>\n<td>0.05<\/td>\n<\/tr>\n<tr>\n<td>Autres Total<\/td>\n<td>\u2014<\/td>\n<td>0.15<\/td>\n<\/tr>\n<tr>\n<td>Aluminium (Al)<\/td>\n<td>\u2014<\/td>\n<td>\u00c9quilibre<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h2>Propri\u00e9t\u00e9s m\u00e9caniques selon le traitement thermique<\/h2>\n<p>The mechanical properties of 3003 square bar depend on the temper and the product form (extruded vs. fabricated from plate). The values below are typical for bar stock. Always request an MTC report for certified values on your specific batch.<\/p>\n<h3>3003-O (recuit)<\/h3>\n<table>\n<thead>\n<tr>\n<th>Propri\u00e9t\u00e9<\/th>\n<th>Valeur typique<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>R\u00e9sistance \u00e0 la traction (MPa)<\/td>\n<td>95 \u2013 130<\/td>\n<\/tr>\n<tr>\n<td>Limite d'\u00e9lasticit\u00e9 (MPa)<\/td>\n<td>\u2265 35<\/td>\n<\/tr>\n<tr>\n<td>\u00c9longation (%)<\/td>\n<td>\u2265 25<\/td>\n<\/tr>\n<tr>\n<td>Duret\u00e9 (Brinell)<\/td>\n<td>~ 28<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h3>3003-H14 (semi-dur)<\/h3>\n<table>\n<thead>\n<tr>\n<th>Propri\u00e9t\u00e9<\/th>\n<th>Valeur typique<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>R\u00e9sistance \u00e0 la traction (MPa)<\/td>\n<td>140 \u2013 180<\/td>\n<\/tr>\n<tr>\n<td>Limite d'\u00e9lasticit\u00e9 (MPa)<\/td>\n<td>\u2265 115<\/td>\n<\/tr>\n<tr>\n<td>\u00c9longation (%)<\/td>\n<td>\u2265 5<\/td>\n<\/tr>\n<tr>\n<td>Duret\u00e9 (Brinell)<\/td>\n<td>~ 40<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h3>3003-H112 (As-Extruded)<\/h3>\n<table>\n<thead>\n<tr>\n<th>Propri\u00e9t\u00e9<\/th>\n<th>Valeur typique<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>R\u00e9sistance \u00e0 la traction (MPa)<\/td>\n<td>95 \u2013 145<\/td>\n<\/tr>\n<tr>\n<td>Limite d'\u00e9lasticit\u00e9 (MPa)<\/td>\n<td>\u2265 35<\/td>\n<\/tr>\n<tr>\n<td>\u00c9longation (%)<\/td>\n<td>\u2265 18<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h2>3003 Aluminum Temper Selection Guide for Square Bar<\/h2>\n<p>Select the right temper for your square bar application based on the required strength, formability, and post-machining stability.<\/p>\n<table>\n<thead>\n<tr>\n<th>Temp\u00e9rer<\/th>\n<th>Description<\/th>\n<th>Avantage principal<\/th>\n<th>When to Use for Square Bar<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>O<\/td>\n<td>Recuit \u2014 enti\u00e8rement mall\u00e9able<\/td>\n<td>Formabilit\u00e9 et ductilit\u00e9 maximales<\/td>\n<td>Deep forming, bending to tight radii, or where the square bar will undergo extensive welding or machining with chip control<\/td>\n<\/tr>\n<tr>\n<td>H14<\/td>\n<td>Durci par d\u00e9formation, demi-dur<\/td>\n<td>Good balance of strength and formability<\/td>\n<td>General fabrication, brackets, structural members that require moderate strength and can be bent to moderate radii<\/td>\n<\/tr>\n<tr>\n<td>H22<\/td>\n<td>Strain-hardened then partially annealed<\/td>\n<td>Stable strength with good formability<\/td>\n<td>Square bar that will be formed after delivery; better long-term stability than H14<\/td>\n<\/tr>\n<tr>\n<td>H112<\/td>\n<td>As-extruded<\/td>\n<td>No special strain-hardening control \u2014 economical<\/td>\n<td>Structural square bar where surface finish and mechanical property consistency are less critical<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h2>Key Characteristics of 3003 Aluminum Square Bar<\/h2>\n<h3>R\u00e9sistance \u00e0 la corrosion<\/h3>\n<p>3003 aluminum offers excellent resistance to atmospheric corrosion, including in marine and industrial environments. The manganese addition suppresses intergranular corrosion, making 3003 square bar suitable for outdoor structural applications, chemical storage, and marine non-critical parts. It performs well in contact with fresh water, mild chemicals, and food products without requiring a protective coating.<\/p>\n<h3>Formabilit\u00e9 et soudabilit\u00e9<\/h3>\n<p>3003 square bar in O, H14, or H22 temper can be cold bent, drilled, tapped, and machined with standard tooling. It is rated as highly weldable by TIG (GTAW), MIG (GMAW), and resistance welding. Filler metal 4043 or 1100 is recommended. Note that welding anneals the heat-affected zone in strain-hardened tempers, reducing local strength \u2014 consider using O temper bar if extensive welding is planned.<\/p>\n<h3>Usinabilit\u00e9<\/h3>\n<p>3003 has fair machinability \u2014 softer than heat-treatable alloys like 6061 or 2011. Use sharp tools, positive rake angles, and appropriate cutting speeds to avoid built-up edge. O temper machines more smoothly than H14; chip breakers are recommended for continuous cuts. For square bar used as a machining blank, centerless or blanchard grinding may be specified for tighter tolerance surfaces.<\/p>\n<h2>Common Applications of 3003 Aluminum Square Bar<\/h2>\n<table>\n<thead>\n<tr>\n<th>L'industrie<\/th>\n<th>Applications<\/th>\n<th>Why 3003 Square Bar Is Used<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Traitement chimique<\/td>\n<td>Tank supports, pipe brackets, walkway framing<\/td>\n<td>Corrosion resistance, weldability, moderate strength<\/td>\n<\/tr>\n<tr>\n<td>HVAC &amp; Ductwork<\/td>\n<td>Duct framing, equipment stands, mounting bars<\/td>\n<td>Formability, corrosion resistance, workability<\/td>\n<\/tr>\n<tr>\n<td>Fabrication g\u00e9n\u00e9rale<\/td>\n<td>Machining blanks, spacers, fixturing, brackets<\/td>\n<td>Square cross-section for easy clamping\/jigging, cost-effective<\/td>\n<\/tr>\n<tr>\n<td>Decorative &amp; Architectural<\/td>\n<td>Trim, railing components, display stands, furniture components<\/td>\n<td>Clean square edges, good surface finish acceptance, formability<\/td>\n<\/tr>\n<tr>\n<td>Storage &amp; Transport<\/td>\n<td>Cargo tie-down bars, rack supports, trailer trim<\/td>\n<td>Weldability, corrosion resistance, cost-effective<\/td>\n<\/tr>\n<tr>\n<td>Food &amp; Beverage Equipment<\/td>\n<td>Washdown frames, equipment supports, conveyor guides<\/td>\n<td>Food-safe, corrosion resistant, easy to clean<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h2>Processing &amp; Surface Finish Notes for 3003 Square Bar<\/h2>\n<p>Linsy can supply 3003 square bar with processing and finishing options applied before delivery:<\/p>\n<ul>\n<li><strong>D\u00e9coupe :<\/strong> CNC band saw, circular saw, or waterjet cutting to custom lengths. Standard cut tolerance is \u00b10.5 mm; tighter tolerance is available on request.<\/li>\n<li><strong>Usinage :<\/strong> Drilling, tapping, countersinking, slitting, and light CNC milling are available. 3003 machines best in O temper; H14 may work-harden during cutting.<\/li>\n<li><strong>Surface Finish:<\/strong> Mill finish is standard. Anodizing (clear or colored), brushing, and polishing are available. Note: 3003 anodizes to a slightly yellowish-grey tone (not the bright silver of 6061) due to its manganese content \u2014 this is normal and does not indicate a defective anodized layer.<\/li>\n<li><strong>Edge Conditioning:<\/strong> Sharp corners can be chamfered or radiused on request to improve handling safety and appearance.<\/li>\n<li><strong>Formation :<\/strong> O temper square bar can be bent to tight radii without cracking. H14 temper can be bent to moderate radii; always test-bend a sample for tight-bend applications.<\/li>\n<li><strong>Soudage :<\/strong> 3003 square bar is fully weldable. Post-weld annealing is not required for O temper; H14 and H22 parts may soften in the heat-affected zone after welding.<\/li>\n<\/ul>\n<h2>Documents relatifs \u00e0 la qualit\u00e9 et contr\u00f4le qualit\u00e9<\/h2>\n<p>Linsy provides the following quality documentation with every 3003 square bar order:<\/p>\n<ul>\n<li><strong>MTC Report (Material Test Certificate):<\/strong> Included with every shipment as standard. Certifies chemical composition and mechanical properties per batch.<\/li>\n<li><strong>SGS Test Reports:<\/strong> Available on request for third-party verification of material properties.<\/li>\n<li><strong>Dimension Inspection Report:<\/strong> Available on request for precision or safety-critical applications.<\/li>\n<li><strong>RoHS \/ REACH Compliance:<\/strong> Available on request confirming material compliance with EU directives.<\/li>\n<\/ul>\n<p>All Linsy facilities are certified under <strong>ISO 9001, ISO 14001, and ISO 45001<\/strong>. Mill test certificates reference the applicable ASTM or EN standard used in production.<\/p>\n<h2>Why Choose Linsy for 3003 Aluminum Square Bar<\/h2>\n<ul>\n<li><strong>ISO-Certified Quality:<\/strong> All Linsy production facilities are certified under ISO 9001, ISO 14001, and ISO 45001. Every square bar shipment includes an MTC report as standard.<\/li>\n<li><strong>Custom Sizes &amp; Low MOQ:<\/strong> From prototype quantities to full production runs. Custom side dimensions, lengths, and surface finishes are available even at low order volumes.<\/li>\n<li><strong>Broad Temper Availability:<\/strong> O, H14, H22, H112, and F tempers in stock or on short lead time. No need to compromise on tempers for your project.<\/li>\n<li><strong>Processing Services:<\/strong> Cut-to-length, CNC machining, surface finishing, and welding support available in-house \u2014 reducing your downstream handling and lead time.<\/li>\n<li><strong>Global Delivery:<\/strong> 10\u201360 days lead time depending on specification and order volume. Shipped to 20+ countries with export-standard packaging.<\/li>\n<li><strong>Technical Support:<\/strong> Linsy engineers can assist with temper selection, formability assessment, and welding recommendations for your specific square bar application.<\/li>\n<\/ul>\n<h2>Ressources connexes<\/h2>\n<ul>\n<li><a href=\"https:\/\/premiumalu.com\/fr\/maitrise-de-lalliage-daluminium-3003-un-guide-complet\/\">Ultimate Guide to 3003 Aluminum Alloy<\/a><\/li>\n<li><a href=\"https:\/\/premiumalu.com\/fr\/trouver-lalliage-daluminium-3003-h14-parfait-aujourdhui\/\">Guide ultime de l'aluminium 3003 H14<\/a><\/li>\n<li><a href=\"https:\/\/premiumalu.com\/fr\/choisir-la-tole-daluminium-parfaite-alliages-3104-vs-3003-vs-3004\/\">Choisir la t\u00f4le d'aluminium id\u00e9ale : les alliages 3104, 3003 et 3004 compar\u00e9s<\/a><\/li>\n<li><a href=\"https:\/\/premiumalu.com\/fr\/comparaison-approfondie-entre-3003-et-6061\/\">3003 vs 6061 Aluminum \u2014 In-Depth Comparison<\/a><\/li>\n<\/ul>\n<h2>3003 Aluminum Square Bar FAQ<\/h2>\n<dl>\n<dt>What is the difference between 3003-H14 and 3003-H22 square bar?<\/dt>\n<dd>H14 is strain-hardened only (higher strength, less formable). H22 is strain-hardened then partially annealed (slightly lower strength, better formability and stability). Choose H22 if the bar will be formed after delivery.<\/dd>\n<dt>What side dimensions are available for 3003 square bar?<\/dt>\n<dd>Standard side dimensions range from 5 mm to 60 mm. Custom sizes up to 100 mm and beyond can be produced by extrusion to your specification. Contact us with your required dimensions for availability and lead time.<\/dd>\n<dt>Can 3003 square bar be used outdoors or in marine environments?<\/dt>\n<dd>3003 has good atmospheric corrosion resistance and is suitable for outdoor and non-immersed marine applications (handrails, brackets, enclosures). For immersed saltwater service, 5052 or 5083 is recommended due to superior pitting resistance.<\/dd>\n<dt>What filler wire should I use when welding 3003 square bar?<\/dt>\n<dd>4043 or 1100 filler wire is recommended for TIG and MIG welding of 3003. 4043 gives better color match after anodizing; 1100 is preferred when maximum corrosion resistance in the weld is required.<\/dd>\n<dt>What is the typical lead time for custom 3003 square bar sizes?<\/dt>\n<dd>Standard sizes are available from stock or with 10\u201360 days lead time. Custom side dimensions or non-standard tempers typically ship within 15\u201345 days depending on volume. Contact us for a lead time estimate on your specific requirement.<\/dd>\n<dt>Does 3003 square bar come with mill test certification?<\/dt>\n<dd>Yes \u2014 every Linsy 3003 square bar shipment includes an MTC (Material Test Certificate) as standard, documenting chemical composition and mechanical properties for the production batch.<\/dd>\n<dt>Can 3003 square bar be anodized for architectural or decorative use?<\/dt>\n<dd>Yes. Note that 3003 anodizes to a slightly yellowish-grey tone rather than the bright silver of anodized 6061, due to its manganese content. For a specific color match in architectural applications, request an anodizing sample before ordering in volume.<\/dd>\n<dt>What is the weight of 3003 square bar? How do I calculate it?<\/dt>\n<dd>Approximate weight is calculated as: side (mm) \u00d7 side (mm) \u00f7 1000 \u00d7 2.7 = kg\/m. For example, a 20 mm square bar weighs approximately 1.08 kg\/m. Request an MTC report for exact weight values on your batch.<\/dd>\n<\/dl>\n<h2>FAQ g\u00e9n\u00e9rale sur les commandes<\/h2>\n<dl>\n<dt>What is the minimum order quantity (MOQ) for 3003 square bar?<\/dt>\n<dd>Linsy supports low MOQs for standard tempers and sizes. Custom dimensions or tempers may require higher minimums. Contact us with your requirement for a specific MOQ quote.<\/dd>\n<dt>Can I order a small quantity for prototyping before a full production run?<\/dt>\n<dd>Yes \u2014 Linsy welcomes prototype and small-batch orders. Many standard sizes are available from stock for immediate shipment.<\/dd>\n<dt>What packaging is used for 3003 square bar exports?<\/dt>\n<dd>Export-standard packaging includes PVC wrap, end caps, and wooden crates or pallets suitable for ocean or air freight. Custom packaging is available for high-value or sensitive-finish orders.<\/dd>\n<dt>Does Linsy provide material certification for EU or North American projects?<\/dt>\n<dd>Yes \u2014 MTC reports are provided as standard. SGS test reports, RoHS\/REACH compliance certificates, and EN 10204 3.1 \/ 3.2 certification are available on request.<\/dd>\n<dt>Can Linsy supply 3003 square bar cut to a specific length?<\/dt>\n<dd>Yes \u2014 cut-to-length is a standard service. Provide your required length and tolerance when requesting a quote.<\/dd>\n<dt>What information should I include in my inquiry for 3003 square bar?<\/dt>\n<dd>Please include: alloy (3003), temper (O\/H14\/H22\/etc.), side dimension (mm), length (mm), quantity (pieces or weight), required standard (ASTM\/EN\/GB), and any surface finish or processing requirements.<\/dd>\n<\/dl>","protected":false},"excerpt":{"rendered":"<p>3003 aluminum square bar is a non-heat-treatable Al-Mn alloy bar with a square cross-section, widely used in structural framing, machining blanks, decorative trim, chemical equipment supports, and general fabrication. It offers excellent corrosion resistance, good formability and weldability, and moderate strength \u2014 approximately 20% stronger than 1100 aluminum. Linsy supplies 3003 square bars in tempers O, H14, H22, H112, and F, with custom side dimensions, cut-to-length service, surface finishing options, and MTC reports included with every order.<\/p>\n<p>\n<strong>Formulaires disponibles :<\/strong> square bar \/ rectangular bar<br \/>\n<strong>Temp\u00e9raments courants :<\/strong> O \/ H14 \/ H22 \/ H112 \/ F<br \/>\n<strong>Assistance technique :<\/strong> cut-to-length \/ CNC machining \/ TIG &amp; MIG welding \/ anodizing \/ brushing \/ polishing<br \/>\n<strong>Documents relatifs \u00e0 la qualit\u00e9 :<\/strong> Rapport MTC fourni avec chaque commande, essais SGS sur demande<\/p>","protected":false},"featured_media":9072,"template":"","meta":{"_seopress_titles_title":"3003 Aluminum Square Bar \u2014 O\/H14\/H22\/H112 Custom Supplier | Linsy Aluminum","_seopress_titles_desc":"Source 3003 aluminum square bar (AlMn1Cu) in O, H14, H22, H112 tempers. Custom side dimensions, MTC report included, ISO 9001 certified. Cut-to-length and machining services available.","_seopress_robots_index":"","_seopress_robots_follow":"","_seopress_robots_imageindex":"","_seopress_robots_snippet":"","_seopress_robots_primary_cat":"none","_seopress_robots_breadcrumbs":"","_seopress_robots_freeze_modified_date":"","_seopress_robots_custom_modified_date":"","_seopress_robots_canonical":"","_seopress_social_fb_title":"","_seopress_social_fb_desc":"","_seopress_social_fb_img":"","_seopress_social_fb_img_attachment_id":0,"_seopress_social_fb_img_width":0,"_seopress_social_fb_img_height":0,"_seopress_social_twitter_title":"","_seopress_social_twitter_desc":"","_seopress_social_twitter_img":"","_seopress_social_twitter_img_attachment_id":0,"_seopress_social_twitter_img_width":0,"_seopress_social_twitter_img_height":0,"_seopress_redirections_value":"","_seopress_redirections_enabled":"","_seopress_redirections_enabled_regex":"","_seopress_redirections_logged_status":"both","_seopress_redirections_param":"","_seopress_redirections_type":301,"_seopress_analysis_target_kw":""},"product_brand":[],"product_cat":[193],"product_tag":[],"class_list":["post-9042","product","type-product","status-publish","has-post-thumbnail","product_cat-aluminum-square-bar","first","instock","shipping-taxable","product-type-simple"],"_links":{"self":[{"href":"https:\/\/premiumalu.com\/fr\/wp-json\/wp\/v2\/product\/9042","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/premiumalu.com\/fr\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/premiumalu.com\/fr\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/premiumalu.com\/fr\/wp-json\/wp\/v2\/media\/9072"}],"wp:attachment":[{"href":"https:\/\/premiumalu.com\/fr\/wp-json\/wp\/v2\/media?parent=9042"}],"wp:term":[{"taxonomy":"product_brand","embeddable":true,"href":"https:\/\/premiumalu.com\/fr\/wp-json\/wp\/v2\/product_brand?post=9042"},{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/premiumalu.com\/fr\/wp-json\/wp\/v2\/product_cat?post=9042"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/premiumalu.com\/fr\/wp-json\/wp\/v2\/product_tag?post=9042"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}