6201 aluminum wire is a heat-treatable, electrical-grade alloy that balances high mechanical strength with good conductivity and corrosion resistance. Supplied mainly in the T81 temper, it is the standard choice for All Aluminum Alloy Conductors (AAAC) and overhead power lines. Linsy draws 6201 wire in a range of diameters and supports custom coil weights, tempers, and processing for utility and industrial projects.
可选格式： wire, sheet / coil / tube / bar / profile
常见脾气： T81, T6, T4, O
处理支持： CNC 加工、激光切割、TIG/MIG 焊接、阳极氧化、抛光、粉末喷涂
质量文件： 每笔订单均附有MTC报告
6201 belongs to the 6000 series (Al-Mg-Si) and is optimized for electrical conductor use rather than general structural work. Compared with the classic 1350 EC grade, 6201 trades some conductivity for substantially higher strength, letting conductors carry heavier mechanical loads with smaller sags. The T81 temper (solution heat treated, cold worked, and artificially aged) delivers the best combination of strength and conductivity for overhead lines.
| 参数 | 厚度范围 |
|---|---|
| 直径 | 0.8 – 30 mm |
| 卷材重量 | Minimum 50 kg, custom on request |
| 情绪 | O、T4、T6、T81 |
| 尺寸公差 | ± 2% (typical) |
| 标准 | ASTM B398/B398M, EN 573, GB/T 3190 |
6201 is also available as sheet, coil, tube, bar, and profile for non-conductor applications. Share your drawing or spec to receive a quote for these forms.
| 名称 | 参考标准 |
|---|---|
| AA / UNS | A96201 |
| EN AW | EN AW-6201 |
| 常用标准 | ASTM B398 (wire), ASTM B211, EN 755, GB/T 3191 |
| Product form focus | Drawn wire for AAAC conductors |
| 要素 | 含量（重量百分比） |
|---|---|
| 硅 (Si) | 0.50 – 0.90 |
| 铁（Fe） | 最大 0.50 |
| 铜 (Cu) | 最大 0.10 |
| 锰 (Mn) | 最大0.03 |
| 镁（Mg） | 0.60 – 0.90 |
| 铬 (Cr) | 最大 0.10 |
| 锌 (Zn) | 最大 0.10 |
| 钛 (Ti) | 最大0.03 |
| 其他，各 | 0.05 最大值 |
| 其他，合计 | 0.15 最大值 |
| 铝 (Al) | 平衡 |
| 脾气 | 抗拉强度 (MPa) | 屈服强度 (MPa) | 伸长率 (%) | 剪切强度（MPa） |
|---|---|---|---|---|
| T81 | 310 min | 275 min | 8 最小值 | 193 |
| T6 | 300 – 330 | 260 – 290 | 8 – 12 | 185 – 195 |
| T4 | 200 – 240 | 110 – 140 | 12 – 16 | 150 – 165 |
| O | ≤ 150 | ≤ 90 | ≥ 18 | ≤ 95 |
Preferred conductor temper. Maximum strength with stable conductivity for overhead AAAC lines.
Good all-round strength for fittings and structural wire where full T81 cold work is not required.
Softer, more formable; used when bending or forming is needed before aging.
Annealed, lowest strength; seldom used for conductors but available for special forming.
Higher strength than 1350 EC wire while keeping useful conductivity for power transmission.
Good atmospheric and coastal corrosion resistance, suitable for exposed overhead lines.
Responds to solution heat treatment and aging for controlled temper properties.
Uniform drawn wire strands cleanly into compact AAAC conductors.
6201 wire is supplied drawn and aged; further cold working or re-aging is not normally required. It can be stranded, baked, and connectorized using standard utility practices. Anodizing is possible for identification but is uncommon on conductors. Welding of finished conductors is generally avoided; mechanical or compression joints are preferred.
每笔订单均附带记录化学成分和力学性能的工厂质保书（MTC）。我们的质量体系已通过ISO 9001、ISO 14001和ISO 45001认证。可根据要求安排第三方SGS检测报告。检验涵盖尺寸、表面状态以及按状态进行的力学性能验证。.
Linsy Aluminum is a Shenzhen-based aluminum manufacturer with more than 20 years of experience supplying the 1000 to 8000 series in plate, bar, tube, wire, coil, profile, and block forms. For 6201 aluminum, we support both off-the-shelf ranges and made-to-order dimensions.
See the blog articles linked below for deeper background, and contact our team for a tailored quote on 6201 aluminum.
6201 typically provides about 52% IACS, lower than 1350 EC wire (about 61% IACS) but with significantly higher strength, which is the reason it is chosen for AAAC.
For conductors, T81 is preferred because the cold-work plus age step gives the highest strength at a stable conductivity. T6 is used where full cold work is not required.
Finished conductors are normally joined with compression or mechanical fittings rather than welding. Welding is not standard practice for strand-in-place lines.
Standard coils start at a 50 kg minimum with custom weights on request. Diameter range is 0.8 to 30 mm.
定制尺寸和热处理状态通常可在10至60天内发货。具体时间窗口请在询价时确认，因其取决于合金、热处理状态、尺寸及订单数量。.
最小起订量灵活，逐案评估。小批量及样品订单通常可以满足；大批量或标准规格订单更具经济性。请提供所需尺寸和数量以获取正式报价。.
每笔订单均附带工厂材质证明书（MTC）。我们的管理体系已通过ISO 9001、ISO 14001及ISO 45001认证。可根据要求安排SGS第三方检测报告。.
可以。我们提供CNC机加工、激光切割、TIG/MIG焊接以及表面处理服务，包括阳极氧化、抛光、粉末喷涂及PVC膜保护。.
请提供您的合金/热处理状态、所需形态、尺寸、数量及任何加工或认证要求。我们的团队将回复包含交货周期和运输条款的报价。.
林西优势
林西铝业是铝加工产品的领先供应商，服务于航空航天、通用工程、汽车、船舶和其他专业工业应用等多个行业。
我们致力于保持最高标准的质量和环境责任，我们的认证证明了这一点：ISO 9001:2008、ISO 14001:2004 和 SGS 认证。
