8011 aluminum (AlFeSi(A)) is one of the most widely used 8000-series alloys, best known as a foil and closure-stock material. It offers good formability, moderate strength, and reliable surface quality for deep drawing and laminating. Linsy supplies 8011 in O, H14, and H18 tempers across foil, sheet, coil, and light bar and tube, with custom dimensions and MTC documentation for every order.
可选格式： 箔材 / 薄板 / 卷材 / 棒材 / 管材
常见脾气： O / H14 / H18
处理支持： slitting / deep drawing / laminating / coating
质量文件： 每笔订单均附有MTC报告
8011 is an aluminum–iron–silicon alloy optimized for thin-gauge and formed products. Its iron and silicon content promotes fine grain and good rollability, while keeping enough ductility for deep drawing. It is the workhorse alloy for household and packaging foil, pharmaceutical closure stock, and a range of formed sheet parts.
典型生产范围如下所列；可根据要求提供定制尺寸。.
| 形式 | 脾气 | 尺寸 | 厚度范围 | 备注 |
|---|---|---|---|---|
| 箔材与卷材 | O、H14、H18 | 厚度 | 0.006 – 0.2 毫米 | Household & packaging foil |
| 片材 | O、H14、H18 | 厚度 | 0.2 – 6 mm | Closure & formed parts |
| 圆棒 | O、H14、H18 | 直径 | 6 – 200 mm | 定尺切割 |
| 管材 | O、H14、H18 | 外径 | 10 – 200 mm | Wall 1 – 20 mm |
| 要素 | 构成（%） |
|---|---|
| 硅 (Si) | 0.50 – 0.90 |
| 铁（Fe） | 0.60 – 1.00 |
| 铜 (Cu) | 最大 0.10 |
| 锰 (Mn) | 0.20（最大值） |
| 镁（Mg） | 0.05 最大值 |
| 铬 (Cr) | 最大 0.10 |
| 锌 (Zn) | 最大 0.10 |
| 钛 (Ti) | 最大 0.10 |
| 其他（每项） | 0.05 最大值 |
| 其他（共计） | 0.15 最大值 |
| 铝 (Al) | 剩余 |
| 脾气 | 拉伸强度（兆帕） | 屈服强度（兆帕） | 伸长率 (%) | 备注 |
|---|---|---|---|---|
| O | 90 – 130 | 35 – 80 | 20 – 30 | Soft, for deep drawing |
| H14 | 140 – 180 | 120 – 160 | 4 – 10 | 半硬态 |
| H18 | 170 – 200 | 150 – 180 | 2 – 5 | Full-hard foil/sheet |
Excellent drawability in O temper makes it the default for foil and closure stock.
Good, clean rolling surface suitable for lamination and printing after treatment.
Adequate for indoor and packaging use; not intended for aggressive marine service.
8011 is well suited to slitting, deep drawing, and laminating. Surface treatments such as coating or printing are common for packaging. It is not a structural alloy and should not be specified where high mechanical load is expected.
每批货物均附有详细说明化学成分和力学测试结果的MTC报告。可根据要求安排第三方检验和SGS测试报告。进料和出料检验涵盖尺寸、表面状况和力学性能。.
Linsy在深圳设有生产基地，拥有超过20年的铝材制造经验，向全球B2B买家供应1000–8000系列合金。我们支持原型件和生产批量的定制尺寸、状态及加工。.
工程指南和规格参考有助于合金选择与设计。以下外部链接供背景阅读之用，应在发布前替换为林赛自有内容（使用前请核实）。.
Primarily foil and closure stock — household foil, packaging, bottle caps, and insulation. It is chosen for formability, not high strength.
O temper gives the best drawability; H14/H18 are used where stiffness is needed after forming.
No. 8011 is a forming/foil alloy with modest strength; use 3xxx, 5xxx, or 6xxx grades for structural load.
标准尺寸通常可在 10 至 60 天内供货，具体取决于合金、回火状态和订单数量。询价时请与我们的销售团队确认确切交期。.
可以。在生产工艺允许的情况下，我们可按客户指定的厚度、宽度、长度、直径和壁厚进行切割。.
每份订单均附带一份材质测试报告。可根据要求安排第三方或 SGS 报告。.
常见选项包括原轧表面、阳极氧化、抛光以及根据合金和应用要求定制的专用涂层。.
林西优势
林西铝业是铝加工产品的领先供应商，服务于航空航天、通用工程、汽车、船舶和其他专业工业应用等多个行业。
我们致力于保持最高标准的质量和环境责任，我们的认证证明了这一点：ISO 9001:2008、ISO 14001:2004 和 SGS 认证。
