Цена на алюминий · 19 ноября 2026 г.
LME $3,095 ▲
SMM A00 $3,334 ▼
Changjiang A00 $3,334 ▼

Алюминиевый квадратный прут 7075-O/T6/T651/T73/T7351

7075 aluminum square bar is solid square stock at 570 MPa in T6 — the strongest aluminium bar in general supply. Specified for high-load keys, wear blocks, die components and tooling where a keyway or a flat has to be machined into the face. Not weldable, and thick sections carry a stress-corrosion risk that T73511 addresses.

Сторона: 5–200 mm
Длина: up to 16,000 mm
Состояния поставки: O / T6 / T6511 / T73 / T73511
Стандарты: ASTM B221, ASTM B211
Документы по качеству: Отчет MTC с каждым заказом

Что такое квадратный пруток из алюминия 7075?

7075 aluminum square bar is solid square stock in Al-Zn-Mg-Cu at 570 MPa in T6 — the strongest aluminium bar in general supply. It is specified when a square part has to be as strong as the material allows and will never be welded: machine keys under high load, wear blocks, die components, jigs and tooling, competition components. Square solid is also what you machine a keyway or a flat into, which is why the profile and the alloy often appear together in tooling work. Two limits belong on the drawing: 7075 is not weldable, and bare 7075 has only moderate corrosion resistance with a real stress-corrosion risk in thick sections. Alloy data: алюминиевый сплав 7075.

Диапазон размеров — сторона и длина

Параметр Диапазон
Длина стороны 5 – 200 mm
Длина До 16 000 мм, резка по индивидуальному заказу
Состояния поставки O / T6 / T6511 / T73 / T73511
Стандарты ASTM B221, ASTM B211

О маркировке. Extruded square bar is stress relieved to T6511 or T73511; T651 and T7351 belong to plate. Where a large square is sawn from plate rather than extruded, the plate designation is the correct one and the certificate will say so — tell us the size and we will confirm which route applies.

Состояния поставки и механические свойства

Темпер Предел прочности при растяжении (МПа) Предел текучести (МПа) Удлинение Сопротивление срезу (МПа)
O 230 – 290 95 – 145 10 – 131ТП3Т 150
T6 540 – 570 480 – 505 8 – 111ТП3Т 330
T6511 540 – 570 480 – 505 8 – 111ТП3Т 330
T73 / T73511 470 – 500 390 – 420 8 – 111ТП3Т 285

Typical AA reference figures; confirm against the MTC. Density 2.81 g/cm³, elastic modulus 71.7 GPa. The T6-to-T73 gap is roughly 70 MPa — that is what stress-corrosion resistance costs on this alloy.

Какое состояние — T6, T6511 или T73511

T6511 is the machining default on solid square bar. A solid section removes a lot of material, and T6 carries residual stress that will bow the bar as it comes off; T6511 is stretched after quenching so it stays straight. On a key or a wear block that has to be flat, this is not a technicality.

T73 и T73511 искусственно перестарены, giving up about 70 MPa for much better resistance to stress-corrosion cracking. Choose them for thick sections, sustained tensile load, or wet and salty service.

7075 vs 2024 vs 6061 Square Bar

Сплав / состояние поставки Предел прочности при растяжении (МПа) Предел текучести (МПа) Свариваемость Область применения
7075-T6 / T6511 570 505 Не свариваем High-load keys, wear blocks, die and tooling components
2024-T351 462 324 Не свариваем Усталостно-критичные детали, аэрокосмические конструкции
6061-T6 / T6511 310 276 Хорошо Machine parts, spacers, jigs, tapped posts

7075 примерно на 85% прочнее, чем 6061, и стоит дороже. Указывайте 7075, когда сечение уже максимально допустимое по конструкции и всё равно разрушается; if a bigger 6061 bar would carry the load, it is cheaper, weldable and more corrosion-tolerant.

Цельный пруток, квадратная труба — и прессованный vs холоднотянутый

Цельный прокат против трубы: tube gives more stiffness per kilogram, but there is no wall to hold a keyway, a thread or a clamp load. A key, a gib, a die insert or a tapped post has to be solid; a frame member should be tube.

Маршрут: small and medium square bar is extruded; large squares are sawn from plate, which is why the designation changes with size on this alloy. Ask for the route to be confirmed on the quotation — it decides the corner radius, the tolerance and the certificate designation together.

Резка, механическая обработка и состояние кромки

On a solid square bar, check straightness before you start machining: put it on a surface plate and look for rock. A bar that has already bowed will machine to a taper no matter how the vice is set, and the cause is residual stress rather than the saw. That check takes a minute and saves a scrapped part.

Резка: sawn to length; 7075 saws hot, so use coolant and a sharp blade to avoid a hardened burr.

Механическая обработка: excellent in T6 and T6511. Sharp carbide, climb-mill where finish matters, and order T6511 so the bar does not relieve stress as material comes off. 7075 work-hardens at the cut if the tool rubs.

Поверхность: anodizing protects less than on 6xxx and darkens; use hard anodizing or a coating where corrosion matters, and consider T73. PVC film on plate-sawn bar protects the faces before machining.

Приложения

High-load machine keys and gibs, wear blocks, die and mould components, jig and fixture blocks, competition and motorsport parts, aerospace fittings, precision spacers, defence equipment.

Документы качества и как указать в заказе

Every order ships with an MTC reporting alloy, temper, side and mechanical results against ASTM B221 or B211. Third-party testing is available on request at additional cost; production runs under ISO 9001, ISO 14001 and ISO 45001 certified systems.

Для расчёта цены за один раунд отправьте: сторона × длина, состояние поставки (T6511 for machining, T73511 for thick or wet service), route if the size is near the extruded limit, конец, финиш, и место назначения.

Почему стоит выбрать Linsy

Алюминиевый завод в Шэньчжэне, более 20 лет в отрасли, поставляет сплавы серий 1000–8000 в стандартных спецификациях и нестандартных размерах.

  • MTC с каждым заказом, с указанием стороны и состояния
  • 7075 square bar 5–200 mm side, up to 16,000 mm length
  • Extruded and plate-sawn routes, with the designation confirmed on the quotation
  • Техническая проверка состояния и толщины сечения до принятия заказа
  • Тестирование SGS по запросу; смешанные по спецификациям и проектным заказам обрабатываются как один заказ

Связанные ресурсы

Квадратный пруток из алюминия 7075 — часто задаваемые вопросы

Q: Why T6511 rather than T6?
A: Because a solid square bar removes a lot of material when machined, and T6 carries residual stress that bows the bar. T6511 is stretched to relieve it — same strength, different stability.

Q: Can I get T651 or T7351 on square bar?
A: Only where the bar is sawn from plate, which happens at larger sizes. Give us the side and we will confirm which route and designation apply.

Q: Can 7075 square bar be welded?
О: Нет. Сварка плавлением вызывает горячее растрескивание и разрушает состояние в зоне термического влияния. Проектируйте под механическое крепление.

Q: Когда следует использовать T73511?
A: Thick sections, sustained tensile load, or wet and salty service — wherever stress-corrosion cracking is a real risk. It gives up about 70 MPa for that resistance.

В: Какие размеры вы поставляете?
A: 5–200 mm side, up to 16,000 mm length, cut to size.

Производственное оборудование

Сертификаты

Склад и запасы

Процесс заказа

Преимущества Linsy

Linsy Aluminum - ведущий поставщик продукции для обработки алюминия, обслуживающий различные отрасли промышленности, включая аэрокосмическую, общее машиностроение, автомобильную, морскую, судостроительную и другие специализированные промышленные приложения.

Мы стремимся поддерживать самые высокие стандарты качества и экологической ответственности, о чем свидетельствуют наши сертификаты: ISO 9001:2008, ISO 14001:2004 и SGS.

Подпишитесь на форму сегодня! Откройте для себя алюминиевые решения премиум-класса с помощью Linsy Alu.

WhatsApp Телефон