7075 aluminum square tube is a hollow square Al-Zn-Mg-Cu section at 570 MPa in T6 — the strongest aluminium tube in general supply. Specified when a square member must carry a load no 6xxx section can, and weight is fixed. Not weldable; the T73511 tempers address stress corrosion in thick walls.
Strana: 10–300 mm
Tloušťka stěny: 1–30 mm
Tempery: O / T6 / T6511 / T73511
Pouze bezešvé
Dokumenty týkající se kvality: Protokol o zkoušce z materiálu (MTC) s každou objednávkou
7075 aluminum square tube is a hollow square Al-Zn-Mg-Cu section at 570 MPa in T6 — the strongest aluminium tube in general supply. It is specified when a square member has to carry a load no 6xxx section can and the weight is fixed by the design: aerospace structure, competition components, high-load machine members. Two limits belong on the drawing: 7075 is not weldable, and it has only moderate corrosion resistance with a stress-corrosion risk in thick walls. Square is also the profile that shows twist most clearly, so straightness matters more here than on round tube. Alloy data: Slitina hliníku 7075.
| Položka | Rozsah |
|---|---|
| Vnější strana | 10 – 300 mm |
| Tloušťka stěny | 1 – 30 mm |
| Délka | Až 16 000 mm, řez na míru |
| Tempery | O / T6 / T6511 / T73511 |
| Normy | ASTM B221, ASTM B241 |
K označení. Extruded tube is stress relieved to T6511 or T73511. T651 and T7351 are plate designations and cannot appear on a hollow-section certificate — if a drawing specifies them on tube, the specification and the product form disagree.
| Temperament | Pevnost v tahu (MPa) | Mez kluzu (MPa) | Prodloužení | Smyk (MPa) |
|---|---|---|---|---|
| O | 230 – 290 | 95 – 145 | 10 – 13% | 150 |
| T6 | 540 – 570 | 480 – 505 | 8 – 11% | 330 |
| T6511 | 540 – 570 | 480 – 505 | 8 – 11% | 330 |
| T73511 | 470 – 500 | 390 – 420 | 8 – 11% | 285 |
Typical AA reference figures; confirm against the MTC. Density 2.81 g/cm³, elastic modulus 71.7 GPa. A square section concentrates stress at the inside corners, so in 7075 the T73 tempers are not a luxury on thick walls — they are what stops a corner crack starting.
T6 je špičková pevnost for a tube machined at the ends and used dry. T6511 má stejnou pevnost, je zbavena pnutí a vyrovnána — worth ordering on long square tube, where twist matters and machining is planned.
T73511 is overaged on purpose, giving up about 70 MPa to buy much better resistance to stress-corrosion cracking. For thick walls, sustained tension, or wet and salty service, that trade is usually correct.
| Slitina / stav | Pevnost v tahu (MPa) | Mez kluzu (MPa) | Kde se hodí |
|---|---|---|---|
| 7075-T6 / T6511 | 570 | 505 | Maximum-strength square members, aerospace, competition |
| 2024-T3 | 483 | 345 | Fatigue-critical square structure |
| 6061-T6 | 310 | 276 | Rámy strojů, regály, ochranné kryty |
7075 is about 85% stronger than 6061 and costs more with fewer suppliers. Specifikujte ji, když je zatížení dáno a hmotnost nesmí narůst; if a thicker 6061 tube would carry the same load, it is cheaper, weldable and more corrosion-tolerant.
Čtvercový dává stejnou tuhost v obou směrech a snáze se detailuje v spojích; obdélníkový umisťuje materiál tam, kde je ohyb and is lighter for a one-direction beam. On 7075 the choice is usually driven by the existing design, because the alloy is specified late in a project rather than at concept stage.
Poloměr rohu is where 7075 is harder than 6xxx: it extrudes less cleanly, so corners are less tight and less consistent. If the joint depends on the corner — a connector or a sliding fit — send the connector drawing rather than assuming a sharp corner.
Twist matters more on square tube than round. A twisted square will not sit flat, will not slide into another section, and pulls a welded frame out of square — and 7075 cannot be straightened by welding or heat. Specify straightness if the assembly is dimensionally critical.
Ohýbání: not practical. Square sections collapse at the corners, and 7075 has low elongation in T6 — it will crack before it forms. Frames are fabricated from mitred segments.
On incoming inspection, check twist before anything else. Put the tube on a surface plate and look for rock; a straightened 7075 square section should sit flat over its length, and a member that rocks will not assemble into a square frame no matter how the holes are drilled. Thickness and side are easy to measure; twist is the defect that reaches the assembly stage and cannot be fixed there.
Řezání a spojování: sawed square or mitred; 7075 saws with heat, so use coolant and a sharp blade to avoid a hardened burr. No welding — design for mechanical fastening or bonding.
Povrch: anodizing protects less than on 6xxx and darkens; use hard anodizing or a coating, and consider T73511 where corrosion matters.
Aerospace structure and fittings, competition vehicle frames, high-load machine members, gantry arms, precision instrument frames, defence equipment, sporting goods components where weight is fixed by design.
Every order ships with an MTC reporting alloy, temper, side, wall and mechanical results against ASTM B221 or B241. For aerospace or pressure work, state the test and certification requirement on the enquiry. Third-party testing is available on request at additional cost; production runs under ISO 9001, ISO 14001 and ISO 45001 certified systems.
Pro nabídku v jednom kole pošlete: strana × stěna × délka, stav zpracování (T6511 pro obrábění, T73511 pro tlusté stěny nebo mokré prostředí), požadavek na přímost, úprava konců, a místo určení.
Hliníkárna se sídlem v Shenzhenu, více než 20 let v oboru, dodávající slitiny řady 1000–8000 ve standardních specifikacích a zakázkových rozměrech.
Q: Is 7075 square tube welded or seamless?
A: Seamless. 7075 does not weld, so a seam-welded product sold as 7075 should be questioned.
Q: Why T6511 and not T651?
A: T651 is a plate designation and cannot appear on a tube certificate. The same applies to T7351 versus T73511.
Q: Can 7075 square tube be bent?
A: No, not practically. Square sections collapse at the corners and 7075 in T6 cracks before it forms. Fabricate from mitred segments.
Q: Does twist matter on square tube?
A: More than on round. A twisted square will not sit flat or slide into another section, and 7075 cannot be straightened afterwards. Specify straightness if the assembly is critical.
Otázka: Jaké rozměry dodáváte?
A: 10–300 mm side, 1–30 mm wall, up to 16,000 mm length.
Výhody Linsy
Společnost Linsy Aluminium je předním dodavatelem výrobků pro zpracování hliníku, které slouží různým průmyslovým odvětvím včetně leteckého průmyslu, všeobecného strojírenství, automobilového průmyslu, lodního průmyslu, stavby lodí a dalších specializovaných průmyslových aplikací.
Zavázali jsme se dodržovat nejvyšší standardy kvality a odpovědnosti vůči životnímu prostředí, což dokazují naše certifikáty: ISO 9001:2008, ISO 14001:2004 a SGS.