A319 (A319.0) is a widely used aluminum-silicon-copper casting alloy known for good castability and cost-effectiveness. The copper addition provides solid strength and hardness, making it a reliable general-purpose foundry alloy. Linsy supplies A319 as ingot, billet, and custom cast components with an MTC on every order.
Dostupné formuláře: ingot / billet / sand casting / permanent-mold casting / die casting
Běžné typy povah: F / T4 / T5 / T6
Podpora zpracování: CNC machining / heat treatment / NDT inspection
Dokumenty týkající se kvality: Protokol o zkoušce z materiálu (MTC) s každou objednávkou
A319 Aluminum Casting Alloy is an aluminum-silicon-copper casting alloy supplied by Linsy for foundries and component manufacturers. It is valued for good castability, reasonable strength, and cost-effectiveness in sand, permanent-mold, and die-casting processes. Linsy provides ingot and billet feedstock as well as custom cast components, with an MTC supplied on every order.
| Formulář | Typical Size / Note |
|---|---|
| Ingot | Standard ingot sizes; custom weights available |
| Billet / Foundry ingot | Custom dimensions on request |
| Cast components | Sand, permanent-mold, and die casting to drawing |
| Sizes and tooling are produced to customer specification. | |
| Standardní | Označení |
|---|---|
| AA / UNS | A319 |
| CS | EN AC-319.0 (casting variant) |
| Common family | Al-Si-Cu casting alloy |
| Prvek | Obsah (%) |
|---|---|
| Si | 5.5 – 6.5 |
| Fe | 0.60 max |
| Cu | 3.0 – 4.5 |
| Mn | max 0,50 |
| Mg | 0,10 max (verify) |
| Zn | 1.0 max |
| Ti | 0.10 – 0.20 |
| Ostatní (každý) | 0,05 max |
| Ostatní (celkem) | 0,15 max |
| Al | Zbytek |
| Temperament | Pevnost v tahu (MPa) | Mez kluzu (MPa) | Prodloužení (%) |
|---|---|---|---|
| F (as-cast) | ~170 | ~95 | ~2 |
| T4 | ~210 | ~110 | ~3 |
| T6 | ~250 | ~165 | ~2 |
| Values shown are typical for the T6 condition and should be confirmed against the mill certificate for a specific casting. | |||
| Majetek | Hodnota |
|---|---|
| Hustota | 2,79 g/cm³ |
| Melting range | 516 – 604 °C |
| Tepelná vodivost | 109 W/m-°C |
| Shear strength (T6) | ~152 MPa |
F (as-cast) is used where no heat treatment is required. T4 (solution + natural age) improves strength and ductility. T5 (artificial age only) gives moderate strength with good dimensional stability. T6 (solution + artificial age) is the most common choice for maximum strength. Select the temper based on the mechanical and thermal demands of the final part.
The silicon content delivers good fluidity and low shrinkage, making the alloy suitable for complex thin-wall castings.
Copper additions raise strength and hardness relative to lower-copper casting grades, supporting structural and wear-facing applications.
The alloy offers fair corrosion resistance. Welding is possible but should be specified with engineering review; post-weld heat treatment may be needed to recover properties.
A319 Aluminum Casting Alloy is normally supplied as ingot/billet or as cast components. Machining is straightforward in the T5/T6 condition. Surface treatments such as anodizing are limited by the high silicon content and should be evaluated case by case. Dimensional and NDT inspection can be arranged to drawing.
Every order ships with an MTC reporting chemical analysis and mechanical results for the lot. Additional inspection such as X-ray, dye penetrant, or pressure testing can be arranged on request.
Linsy is a Shenzhen-based aluminum supplier with more than 20 years of production experience across the 1000 to 8000 series, including casting feedstock and custom cast parts. We support custom chemistries, sizes, and light processing, and back each shipment with full mill documentation.
For background on aluminum casting alloys, see the references below (external — verify and replace with Linsy-owned content before publishing):
A319 is a general-purpose Al-Si-Cu casting alloy used for automotive and industrial castings where good strength and castability are needed.
Yes. It is commonly supplied in the T5 or T6 condition to improve strength and hardness; the right temper depends on the part’s service requirements.
No. A319.0 is one variant of the 319 family. A380 has higher silicon and different copper limits; always confirm the exact designation on the mill certificate.
Lead times generally range from 10 to 60 days depending on alloy, form, and quantity. Confirm with your quote.
Yes. An MTC is supplied with every order, and additional inspection can be arranged on request.
Yes. We produce ingot, billet, and cast components to customer drawings and specifications.
Výhody Linsy
Společnost Linsy Aluminium je předním dodavatelem výrobků pro zpracování hliníku, které slouží různým průmyslovým odvětvím včetně leteckého průmyslu, všeobecného strojírenství, automobilového průmyslu, lodního průmyslu, stavby lodí a dalších specializovaných průmyslových aplikací.
Zavázali jsme se dodržovat nejvyšší standardy kvality a odpovědnosti vůči životnímu prostředí, což dokazují naše certifikáty: ISO 9001:2008， ISO 14001:2004 a SGS.
