5052 aluminum round bar is a non-heat-treatable 5xxx-series alloy prized for its exceptional corrosion resistance, particularly in saltwater and marine environments. Supplied in O, H32, and H34 tempers, it combines excellent formability with moderate strength and outstanding weldability. Linsy manufactures and stocks 5052 round bars in a wide range of standard and custom diameters, cut to length and backed by a Mill Test Certificate (MTC) with every order.
Dostupné formuláře: round bar / rod (custom profiles on request)
Běžné typy povah: O / H32 / H34
Podpora zpracování: CNC cutting / peeling / chamfering / centerless grinding / anodizing
Dokumenty týkající se kvality: MTC report with every order; SGS test reports available on request
5052 aluminum round bar is a solid cylindrical product made from the 5052 aluminum alloy (EN AW-5052 / A95052), a non-heat-treatable 5xxx-series alloy with magnesium as its primary alloying element (2.2–2.8%). The round bar form is one of the most commonly stocked shapes for this grade, valued for its balance of corrosion resistance, formability, and moderate strength.
Unlike heat-treatable alloys such as 6061 or 7075, 5052 gains its strength through strain hardening (cold working). It is supplied in H32 and H34 tempers — stabilized tempers that retain about 1/4 and 1/2 hard cold-work, respectively — as well as the fully annealed O temper for maximum formability. This makes 5052 round bar suitable for marine hardware, fuel tank fittings, pressure vessel components, and general structural and decorative applications where corrosion resistance is critical.
Standard designations include ASTM B221, GB/T 3190, JIS H4000a AMS 4015 (sheet equivalent). Linsy supplies 5052 round bars to these specifications with full traceability documentation.
| Položka | Specifikace |
|---|---|
| Slitina | 5052 (EN AW-5052 / A95052) |
| Temperament | O, H32, H34 |
| Průměr (mm) | 6 – 300 |
| Délka (mm) | 1000 – 6000 (custom cut to length) |
| Standardní | ASTM B221, GB/T 3190, JIS H4000, AMS 4015 |
| Povrchová úprava | Mill finish, polished, anodized (on request) |
| Tolerance | Per ASTM B221 or as agreed |
Custom diameters, lengths, and tolerance grades are available on request. Linsy supports both standard stock sizes and made-to-order production runs with low MOQs.
The table below shows the nominal chemical composition of 5052 aluminum per GB/T 3190 and ASTM standards. Magnesium is the primary alloying element, responsible for the alloy’s strength and corrosion resistance. Chromium refines the grain structure and improves stress-corrosion cracking resistance.
| Prvek | Obsah (%) |
|---|---|
| Si | 0,25 max. |
| Fe | max 0,40 |
| Cu | 0,10 max |
| Mn | 0,10 max |
| Mg | 2.2 – 2.8 |
| Cr | 0.15 – 0.35 |
| Zn | 0,10 max |
| Al | Bilance |
Because 5052 is a non-heat-treatable alloy, its mechanical properties depend on the temper — specifically the degree of cold work applied. The values below are typical for 5052 round bar in the most common tempers. Actual properties may vary with bar diameter and production lot; certified values are provided on the MTC with each shipment.
| Majetek | O (žíhaný) | H32 (1/4 Hard) | H34 (1/2 Hard) |
|---|---|---|---|
| Ultimate Tensile Strength (MPa) | 175 – 215 | 205 – 240 | 230 – 270 |
| Mez kluzu (MPa) | 65 – 80 | 130 – 155 | 150 – 180 |
| Prodloužení při přetržení (%) | 20 – 25 | 12 – 18 | 10 – 14 |
| Hardness (Brinell, HB) | ~47 | ~60 | ~68 |
The original source listed a single tensile strength (210 MPa) and yield strength (135 MPa) without specifying the temper. These values are consistent with H32 typical properties. The ranges above reflect published industry data; certified lot-specific values accompany every shipment.
Choosing the right temper for 5052 aluminum round bar depends on the balance between formability and strength required by your application:
The softest condition, offering maximum formability and ductility. Best for applications requiring severe bending, forming, or drawing. Strength is the lowest of the three common tempers.
Strain-hardened and then stabilized to maintain properties over time. Offers a good balance of strength and formability — the most popular choice for general-purpose round bar applications including marine fittings and structural components.
Higher cold-work content than H32, giving greater strength and hardness at the expense of some ductility. Suitable for components that require higher load-bearing capacity but less forming during fabrication.
Not sure which temper fits your project? Contact Linsy’s technical team for guidance based on your application requirements.
5052 aluminum offers outstanding resistance to saltwater, marine atmospheres, and a wide range of chemicals. The magnesium content forms a stable, self-healing oxide layer that protects the surface even in harsh environments. This makes 5052 round bar a preferred material for marine hardware, pump shafts, and chemical processing equipment.
As a non-heat-treatable alloy, 5052 can be readily bent, formed, and machined. The O temper offers the highest formability, while H32 and H34 still permit moderate cold forming. The alloy machines cleanly with appropriate speeds and feeds.
5052 welds readily using gas tungsten arc welding (GTAW/TIG), gas metal arc welding (GMAW/MIG), and resistance welding. Weld joint efficiency is high, and the heat-affected zone retains good corrosion resistance. 5052 filler wire (ER5356 or ER5554) is typically recommended.
While not as strong as 2xxx or 7xxx series alloys, 5052 provides adequate strength for many structural and mechanical applications. Its strength-to-weight ratio is competitive for corrosion-critical service where higher-strength alloys would require protective coatings.
Linsy provides a range of in-house and partnered processing services for 5052 aluminum round bar:
Processing availability and lead time depend on the specific operation, bar diameter, and order quantity. Contact our team to confirm capability for your project.
Every 5052 aluminum round bar shipment from Linsy is accompanied by the following quality documentation:
Linsy operates under a certified quality management system aligned with ISO 9001, ISO 14001, and ISO 45001 standards. Material traceability is maintained from ingot to finished bar through heat-number tracking.
With over 20 years of experience in aluminum manufacturing, Linsy supplies 5052 aluminum round bars to customers in 20+ countries. Our production capabilities cover standard stock sizes and custom specifications, with low MOQs to support both prototyping and volume production.
Request a quote for your 5052 aluminum round bar project today.
H32 is a 1/4-hard stabilized temper offering a balance of strength and formability. H34 is a 1/2-hard stabilized temper with higher tensile and yield strength but reduced ductility. Choose H32 for general-purpose applications and moderate forming; choose H34 when higher strength is the priority.
Yes. 5052 has excellent weldability using TIG (GTAW) and MIG (GMAW) processes. ER5356 or ER5554 filler wire is recommended. The weld zone retains good corrosion resistance, making 5052 suitable for welded structures in marine and chemical environments.
Linsy supplies 5052 round bar in diameters from 6 mm to 300 mm. Standard sizes are typically in stock, and custom diameters can be produced to order. Please contact us with your specific size requirements.
Lead time typically ranges from 10 to 60 days depending on the specification, temper, quantity, and any required processing. Stock items can often ship faster. Contact our team for a lead-time estimate on your specific order.
Linsy supports low MOQs to accommodate both prototyping and production runs. The exact minimum depends on the diameter, temper, and processing required. Please share your requirements for a specific MOQ quote.
Yes. An MTC is included with every order, certifying the chemical composition and mechanical properties of the material. SGS third-party test reports are also available on request.
5052 round bar is commonly supplied to ASTM B221, GB/T 3190, JIS H4000, and AMS specifications. Linsy can produce to specific customer or industry standards on request.
Výhody Linsy
Společnost Linsy Aluminium je předním dodavatelem výrobků pro zpracování hliníku, které slouží různým průmyslovým odvětvím včetně leteckého průmyslu, všeobecného strojírenství, automobilového průmyslu, lodního průmyslu, stavby lodí a dalších specializovaných průmyslových aplikací.
Zavázali jsme se dodržovat nejvyšší standardy kvality a odpovědnosti vůči životnímu prostředí, což dokazují naše certifikáty: ISO 9001:2008， ISO 14001:2004 a SGS.
