5083 aluminum round tube is a non-heat-treatable, high-magnesium alloy (AlMg4.5Mn0.7) built for marine and offshore service. It offers excellent seawater corrosion resistance, retains strength after welding, and performs well at cryogenic temperatures. Linsy supplies it in O, H111, H112, H116, and H321 tempers with custom outer diameters and wall thicknesses.
Mevcut formlar: round tube / pipe
Yaygın temperler: O / H111 / H112 / H116 / H321
İşleme desteği: CNC cutting, bending, TIG/MIG welding, anodizing, polishing
Kalite belgeleri: Her siparişle birlikte MTC raporu
5083 Aluminum Round Tube is a non-heat-treatable aluminum-magnesium alloy (AlMg4.5Mn0.7) supplied by Linsy Aluminum. It is one of the strongest work-hardenable grades and is widely specified for marine, offshore, and cryogenic service because of its excellent resistance to seawater corrosion and its ability to retain strength after welding. Common tempers include O, H111, H112, H116, and H321.
| Dış Çap | 6 – 400 mm |
|---|---|
| Wall Thickness | 0.5 – 40 mm |
| Uzunluk | 1000 – 6000 mm (custom) |
| Common Tempers | O, H111, H112, H116, H321 |
| Standards | ASTM B221, EN 755, GB/T 6893 |
Dimensions can be customized to customer drawings. Share your required size and temper for a quote.
| Standart | Tanımlama |
|---|---|
| AA / UNS | 5083 / A95083 |
| EN | EN AW-AlMg4.5Mn0.7 |
| ISO | AlMg4.5Mn0.7 |
| GB/T | 5A05 (closest domestic grade) |
| JIS | A5083 |
The composition below follows the AA 5083 specification (AlMg4.5Mn0.7). Values are typical ranges; the supplied MTC reports the actual analysis of your lot.
| Element | Yüzde % |
|---|---|
| Si | 0,40 maks |
| Fe | 0,40 maks |
| Cu | 0,10 maks. |
| Mn | 0,40 – 1,00 |
| Mg | 4.00 – 4.90 |
| Cr | 0,05 – 0,25 |
| Zn | 0,25 maks. |
| Ti | 0,15 maks. |
| Diğerleri (her biri) | 0,05 maks. |
| Diğerleri (toplam) | 0,15 maks. |
| Al | Denge |
Values below are typical room-temperature properties for 5083 tube and extrusion. Actual results depend on temper, section, and thickness and are reported on the MTC.
| Temper | Çekme Dayanımı (MPa) | Akma Dayanımı (MPa) | Uzama (%) | Brinell Sertlik |
|---|---|---|---|---|
| O | 275 – 350 | 110 – 145 | 16 – 21 | ~75 |
| H111 | 275 – 350 | ≥175 | 16 | ~75 |
| H112 | ≥275 | ≥125 | ≥12 | ~75 |
| H116 / H321 | 305 – 385 | ≥215 | ≥10 | ~85 |
| H32 | 305 – 345 | ≥215 | ≥12 | ~85 |
5083 is non-heat-treatable — tempers are produced by strain hardening and stabilization, not by solution heat treatment.
5083 resists seawater and industrial atmospheres better than most aluminum alloys, making it the default marine grade.
Among the strongest work-hardenable aluminum alloys, with good strength even at low temperatures.
Welds cleanly with TIG/MIG; strength in the weld zone is largely retained when using ER5183 or ER5356 filler.
Toughness and strength are maintained at very low temperatures, suitable for LNG and cryogenic tanks.
5083 welds well with conventional processes (TIG/MIG) and retains most of its strength in the weld zone. For welding filler, ER5183 or ER5356 wire is commonly used. The alloy has only moderate machinability compared with heat-treatable grades, and cutting tools should account for its gummy chip formation.
Every 5083 order ships with a material test certificate (MTC) that reports the actual chemical analysis and mechanical results for the supplied lot. Third-party SGS test reports are available on request. Standard mill inspections cover dimensional tolerance, surface condition, and tensile verification per the ordered specification.
Linsy Aluminum is a Shenzhen-based aluminum manufacturer with over 20 years of production experience, supplying the 1000–8000 series across plate, bar, tube, wire, coil, profile, and block. For 5083 round tube, we support custom dimensions, small minimum order quantities, and short lead times.
Typical wall thickness ranges from 0.5 mm to 40 mm, with outer diameters from 6 mm to 400 mm. Other dimensions can be produced to drawing.
Yes. H116/H321 tempers are widely used in pressure vessels and tanks where corrosion resistance and weld integrity matter.
Yes. It is one of the most weldable aluminum alloys; use ER5183 or ER5356 filler and control heat input.
Custom 5083 orders are usually produced and shipped within 10–60 days, depending on temper, size, and quantity. Contact us with your drawing or specification for a firm schedule.
We support low minimum order quantities for standard tempers and common sizes. Non-standard dimensions are quoted case by case.
Yes. A material test certificate (MTC) is provided with every order, and third-party SGS test reports are available on request.
Mill finish is standard. Anodizing, polishing, powder coating, and PVC film protection can be arranged.
Yes. CNC cutting, sawing, and machining services are available so material arrives closer to your net shape.
Linsy Avantajları
Linsy Alüminyum, havacılık, genel mühendislik, otomotiv, denizcilik, gemi yapımı ve diğer özel endüstriyel uygulamalar dahil olmak üzere çeşitli endüstrilere hizmet veren lider bir alüminyum işleme ürünleri tedarikçisidir.
Sertifikalarımızın da gösterdiği gibi, en yüksek kalite ve çevresel sorumluluk standartlarını sürdürmeye kararlıyız: ISO 9001:2008 ， ISO 14001:2004 ve SGS.
