Preço do Alumínio · 20 de novembro de 2026
LME $3,184.5 ▲
SMM A00 $3,353 ▲
Changjiang A00 $3,344 ▼

1370-O/H14/H18 Fio de alumínio

1370 aluminum wire is a high-purity conductor grade at 99.7% minimum, used where the loss budget justifies the extra purity — about 61.5% IACS against 61% for 1350. The gain looks small until it is multiplied by kilometres of conductor and years of operation.

Diâmetro: 0,8–30 mm
Temperamentos: O / H14 / H18
Peso da bobina: 50–500 kg
Purity: 99.7% Al minimum
Documentos de qualidade: MTC with conductivity, tensile and purity

O Que É o Fio de Alumínio 1370?

1370 aluminum wire is a high-purity electrical conductor grade with a minimum aluminium content of 99.7%, used where the loss budget is tight enough that the extra purity pays for itself. Conductivity runs about 61.5% IACS — marginally better than 1350 EC — with similar strength in the hard-drawn condition. The difference looks small until it is multiplied by kilometres of conductor and decades of operation. Alloy data: Liga de alumínio 1370.

Diâmetro, Tolerância e Peso do Rolo

Temperamento Diâmetro (mm) Coil weight (kg) Condição
O 0,8 – 30 50 – 500 Annealed, maximum ductility for drawing and stranding
H14 0,8 – 30 50 – 500 Intermediate strength
H18 0,8 – 30 50 – 500 Hard drawn for conductor

Tolerance is ±0.02–0.05 mm drawn, tighter on request. On a stranding line the tolerance controls lay length and tension, so state the class rather than leaving it to the standard.

Temperamentos e Propriedades Mecânicas

Temperamento Tração (MPa) Condutividade (% IACS) Uso típico
O ~70–95 ~62 Annealed, winding and flexible conductors
H14 ~100–140 ~61.5 Intermediate, formed parts
H18 ~170–200 ~61.5 Hard drawn conductor

Typical values; confirm against the MTC. Density 2.70 g/cm³, resistivity about 0.0280 Ω·mm²/m at 20 °C. The advantage over 1350 is in the metal, not the temper: higher purity means fewer scattering sites and less resistive loss.

Qual Têmpera — O, H14 ou H18

H18 is the conductor temper for overhead and cable work where the wire has to hold stringing tension. O é para enrolamentos e flexibilidade — the condition for anything that bends repeatedly. H14 sits between and is used where some strength is needed without a full hard draw. As with 1350, an over-annealed H18 becomes effectively O and will not hold sag.

1370 vs 1350 vs 6201 Conductor Wire

Liga metálica Tração (MPa) Condutividade (% IACS) Onde se aplica
1370-H18 ~170–200 ~61.5 Condutor com prioridade em condutividade
1350-H19 ~160–200 ~61 Standard EC grade, the default
6201-T81 ~295 ~52 Long spans where strength governs

1370 buys about half a point of conductivity over 1350 at a higher metal cost — worth it on high-load-factor lines and in wound applications, not worth it on short runs. When strength is the constraint rather than loss, neither answer is right and 6201 is.

Fio para condutores ou fio mecânico — e o que decide

Conductor wire is judged on conductivity, strength and stranding behaviour; mechanical wire on formability, weldability or corrosion. 1370 belongs firmly to the first family — it is not a structural or welding wire, and its low alloy content means it has little strength to offer outside electrical work.

Certification is part of the product: conductivity on the finished wire, reported with tensile on the same document.

Como a condutividade é especificada. A condutividade é expressa como porcentagem do Padrão Internacional de Cobre Recozido, portanto 61% IACS significa 61% da condutividade do cobre recozido. É medida no fio acabado, por resistência por unidade de comprimento a uma temperatura declarada (normalmente 20 °C), e como a resistência do alumínio sobe cerca de 0,4% por °C, a temperatura de medição tem de ser declarada, caso contrário o número não significa nada. É por isso que um certificado de condutor reporta condutividade e temperatura de ensaio em conjunto, e por que uma leitura à temperatura ambiente feita numa manhã fria pode ser contestada.

Half a point of conductivity is not a rounding error: on a 200 km line at high load factor it is a measurable energy saving over the asset life, and that is the only calculation that justifies the higher-purity metal. If the line is short or lightly loaded, 1350 wins on cost and nobody notices the difference.

Trefilação, Bobinagem e Superfície

Trefilação: bright drawn to finish diameter with lubricant removed. On a high-purity grade, surface contamination matters more than on an alloy wire, because there is no alloying element to mask it — a contaminated surface is a local hot spot.

Bobinagem: coils 50–500 kg, spools on request; give the spool type and bore your payoff accepts.

Junção: compression fittings and splices on conductor; welding is possible but anneals the joint and reduces its current capacity.

Annealing control is the other variable on this grade. 1370 softens at a low temperature, and an over-annealed H18 coil becomes effectively O — it will not hold sag on the line, and the fault appears only when the conductor is strung. If the wire is annealed or heat-treated anywhere in your process, tell us the thermal history so the temper we supply accounts for it.

Aplicativos

High-efficiency overhead conductors, cable cores, transformer and reactor windings, busbar and substation connections, flexible braids, precision electrical components.

Documentos de Qualidade e Como Especificar

Every order ships with an MTC reporting alloy, temper, diameter, tensile strength and conductivity measured on the finished wire, plus the purity check that distinguishes 1370 from 1350. Third-party testing is available on request; production runs under ISO 9001, ISO 14001 and ISO 45001 certified systems.

Para cotar em uma única rodada, envie: diâmetro e tolerância, tempera (H18 for conductor, O for winding), peso da bobina ou carretel, conductivity and purity requirement, padrão de superfície, e o destino.

Por que escolher a Linsy

Fábrica de alumínio sediada em Shenzhen, com mais de 20 anos no setor, fornecendo ligas das séries 1000–8000 em especificações padrão e tamanhos personalizados.

  • MTC with conductivity, tensile and purity on the same certificate
  • 1370 wire 0.8–30 mm, coils 50–500 kg, in O, H14 and H18
  • Spools on request, to your payoff bore
  • Trefilado brilhante com lubrificante removido
  • Testes SGS sob solicitação; pedidos com especificações mistas e de projeto tratados como um único pedido

**Recursos Relacionados**

Perguntas Frequentes sobre Fio de Alumínio 1370

Q: Is 1370 worth the extra cost over 1350?
A: On high-load-factor lines and wound applications, yes — about half a point of conductivity compounds over decades. On short runs, 1350 is the value choice.

Q: How is 1370 different from 1350?
A: Purity. 1370 is 99.7% minimum against 99.5%, which means fewer scattering sites and slightly lower resistance. Strength is comparable.

Q: H18 or O?
A: H18 for overhead conductor where stringing tension matters; O for windings and flexible connections.

Q: Does surface condition matter on this grade?
A: More than on an alloy wire — there is no alloying element to mask contamination, and a dirty surface becomes a local hot spot.

P: Quais tamanhos e bobinas vocês fornecem?
A: 0.8–30 mm diameter, coils 50–500 kg, spools on request.

Equipamentos de produção

Certificações

Armazém e estoque

Processo de pedido

Vantagens da Linsy

A Linsy Aluminum é uma fornecedora líder de produtos de processamento de alumínio, atendendo a diversos setores, incluindo aeroespacial, engenharia geral, automotivo, marítimo, construção naval e outras aplicações industriais especializadas.

Temos o compromisso de manter os mais altos padrões de qualidade e responsabilidade ambiental, conforme demonstrado por nossas certificações: ISO 9001:2008, ISO 14001:2004 e SGS.

Assine o formulário hoje mesmo! Descubra suas soluções de alumínio premium com a Linsy Alu.

WhatsApp Telefone