Preço do Alumínio · 20 de novembro de 2026
LME $3,105 ▲
SMM A00 $3,354 ▲
Changjiang A00 $3,345 ▼

Barra quadrada de alumínio 7075-O/T6/T651/T73/T7351

7075 aluminum square bar is solid square stock at 570 MPa in T6 — the strongest aluminium bar in general supply. Specified for high-load keys, wear blocks, die components and tooling where a keyway or a flat has to be machined into the face. Not weldable, and thick sections carry a stress-corrosion risk that T73511 addresses.

Lado: 5–200 mm
Comprimento: up to 16,000 mm
Temperamentos: O / T6 / T6511 / T73 / T73511
espessuras, larguras e comprimentos não padronizados cortados sob encomenda. ASTM B221, ASTM B211
Documentos de qualidade: Relatório MTC em cada pedido

O que é a Barra Quadrada de Alumínio 7075?

7075 aluminum square bar is solid square stock in Al-Zn-Mg-Cu at 570 MPa in T6 — the strongest aluminium bar in general supply. It is specified when a square part has to be as strong as the material allows and will never be welded: machine keys under high load, wear blocks, die components, jigs and tooling, competition components. Square solid is also what you machine a keyway or a flat into, which is why the profile and the alloy often appear together in tooling work. Two limits belong on the drawing: 7075 is not weldable, and bare 7075 has only moderate corrosion resistance with a real stress-corrosion risk in thick sections. Alloy data: Liga de alumínio 7075.

Faixa de tamanho — Lado e Comprimento

Item Faixa
Comprimento do lado 5 – 200 mm
Comprimento Até 16.000 mm, corte personalizado
Temperos O / T6 / T6511 / T73 / T73511
Normas ASTM B221, ASTM B211

Sobre a designação. Extruded square bar is stress relieved to T6511 or T73511; T651 and T7351 belong to plate. Where a large square is sawn from plate rather than extruded, the plate designation is the correct one and the certificate will say so — tell us the size and we will confirm which route applies.

Temperamentos e Propriedades Mecânicas

Temperamento Tração (MPa) Limite de Escoamento (MPa) Alongamento Cisalhamento (MPa)
O 230 – 290 95 – 145 10 – 13% 150
T6 540 – 570 480 – 505 8 – 11% 330
T6511 540 – 570 480 – 505 8 – 11% 330
T73 / T73511 470 – 500 390 – 420 8 – 11% 285

Typical AA reference figures; confirm against the MTC. Density 2.81 g/cm³, elastic modulus 71.7 GPa. The T6-to-T73 gap is roughly 70 MPa — that is what stress-corrosion resistance costs on this alloy.

Qual estado — T6, T6511 ou T73511

T6511 is the machining default on solid square bar. A solid section removes a lot of material, and T6 carries residual stress that will bow the bar as it comes off; T6511 is stretched after quenching so it stays straight. On a key or a wear block that has to be flat, this is not a technicality.

T73 e T73511 são sobreenvelhecidos propositadamente, giving up about 70 MPa for much better resistance to stress-corrosion cracking. Choose them for thick sections, sustained tensile load, or wet and salty service.

7075 vs 2024 vs 6061 Square Bar

Liga / temperamento Tração (MPa) Limite de Escoamento (MPa) Soldabilidade Onde se aplica
7075-T6 / T6511 570 505 Não soldável High-load keys, wear blocks, die and tooling components
2024-T351 462 324 Não soldável Peças críticas à fadiga, estrutura aeroespacial
6061-T6 / T6511 310 276 Bom Machine parts, spacers, jigs, tapped posts

O 7075 é cerca de 85% mais resistente que o 6061 e custa mais por isso. Especifique 7075 quando a seção já for tão grande quanto o projeto permite e ainda assim falhar; if a bigger 6061 bar would carry the load, it is cheaper, weldable and more corrosion-tolerant.

Barra maciça, tubo quadrado — e extrudido vs trefilado a frio

Sólido versus tubo: tube gives more stiffness per kilogram, but there is no wall to hold a keyway, a thread or a clamp load. A key, a gib, a die insert or a tapped post has to be solid; a frame member should be tube.

Rota: small and medium square bar is extruded; large squares are sawn from plate, which is why the designation changes with size on this alloy. Ask for the route to be confirmed on the quotation — it decides the corner radius, the tolerance and the certificate designation together.

Corte, Usinagem e Condição de Borda

On a solid square bar, check straightness before you start machining: put it on a surface plate and look for rock. A bar that has already bowed will machine to a taper no matter how the vice is set, and the cause is residual stress rather than the saw. That check takes a minute and saves a scrapped part.

Corte: sawn to length; 7075 saws hot, so use coolant and a sharp blade to avoid a hardened burr.

**Usinagem:** excellent in T6 and T6511. Sharp carbide, climb-mill where finish matters, and order T6511 so the bar does not relieve stress as material comes off. 7075 work-hardens at the cut if the tool rubs.

Superfície: anodizing protects less than on 6xxx and darkens; use hard anodizing or a coating where corrosion matters, and consider T73. PVC film on plate-sawn bar protects the faces before machining.

Aplicativos

High-load machine keys and gibs, wear blocks, die and mould components, jig and fixture blocks, competition and motorsport parts, aerospace fittings, precision spacers, defence equipment.

Documentos de Qualidade e Como Especificar

Every order ships with an MTC reporting alloy, temper, side and mechanical results against ASTM B221 or B211. Third-party testing is available on request at additional cost; production runs under ISO 9001, ISO 14001 and ISO 45001 certified systems.

Para cotar em uma única rodada, envie: lado × comprimento, tempera (T6511 for machining, T73511 for thick or wet service), route if the size is near the extruded limit, acabamento das extremidades, e o destino.

Por que escolher a Linsy

Fábrica de alumínio sediada em Shenzhen, com mais de 20 anos no setor, fornecendo ligas das séries 1000–8000 em especificações padrão e tamanhos personalizados.

  • MTC com cada encomenda, indicando lado e temper
  • 7075 square bar 5–200 mm side, up to 16,000 mm length
  • Extruded and plate-sawn routes, with the designation confirmed on the quotation
  • Verificação técnica do temperamento e espessura da seção antes da aceitação do pedido
  • Testes SGS sob solicitação; pedidos com especificações mistas e de projeto tratados como um único pedido

**Recursos Relacionados**

Perguntas Frequentes sobre Barra Quadrada de Alumínio 7075

Q: Why T6511 rather than T6?
A: Because a solid square bar removes a lot of material when machined, and T6 carries residual stress that bows the bar. T6511 is stretched to relieve it — same strength, different stability.

Q: Can I get T651 or T7351 on square bar?
A: Only where the bar is sawn from plate, which happens at larger sizes. Give us the side and we will confirm which route and designation apply.

Q: Can 7075 square bar be welded?
R: Não. A soldagem por fusão causa trincas a quente e destrói o têmper na zona afetada pelo calor. Projete para fixação mecânica.

P: Quando devo usar T73511?
A: Thick sections, sustained tensile load, or wet and salty service — wherever stress-corrosion cracking is a real risk. It gives up about 70 MPa for that resistance.

P: Quais tamanhos vocês fornecem?
A: 5–200 mm side, up to 16,000 mm length, cut to size.

Equipamentos de produção

Certificações

Armazém e estoque

Processo de pedido

Vantagens da Linsy

A Linsy Aluminum é uma fornecedora líder de produtos de processamento de alumínio, atendendo a diversos setores, incluindo aeroespacial, engenharia geral, automotivo, marítimo, construção naval e outras aplicações industriais especializadas.

Temos o compromisso de manter os mais altos padrões de qualidade e responsabilidade ambiental, conforme demonstrado por nossas certificações: ISO 9001:2008, ISO 14001:2004 e SGS.

Assine o formulário hoje mesmo! Descubra suas soluções de alumínio premium com a Linsy Alu.

WhatsApp Telefone