7075 aluminum square bar is solid square stock at 570 MPa in T6 — the strongest aluminium bar in general supply. Specified for high-load keys, wear blocks, die components and tooling where a keyway or a flat has to be machined into the face. Not weldable, and thick sections carry a stress-corrosion risk that T73511 addresses.
Seite: 5–200 mm
Länge: up to 16,000 mm
Zustände: O / T6 / T6511 / T73 / T73511
Normen: ASTM B221, ASTM B211
Qualitätsdokumente: MTC-Bericht bei jeder Bestellung
7075 aluminum square bar is solid square stock in Al-Zn-Mg-Cu at 570 MPa in T6 — the strongest aluminium bar in general supply. It is specified when a square part has to be as strong as the material allows and will never be welded: machine keys under high load, wear blocks, die components, jigs and tooling, competition components. Square solid is also what you machine a keyway or a flat into, which is why the profile and the alloy often appear together in tooling work. Two limits belong on the drawing: 7075 is not weldable, and bare 7075 has only moderate corrosion resistance with a real stress-corrosion risk in thick sections. Alloy data: 7075 Aluminiumlegierung.
| Artikel | Bereich |
|---|---|
| Seitenlänge | 5 – 200 mm |
| Länge | Bis zu 16.000 mm, kundenspezifisch geschnitten |
| Gefühle | O / T6 / T6511 / T73 / T73511 |
| Normen | ASTM B221, ASTM B211 |
Zur Bezeichnung. Extruded square bar is stress relieved to T6511 or T73511; T651 and T7351 belong to plate. Where a large square is sawn from plate rather than extruded, the plate designation is the correct one and the certificate will say so — tell us the size and we will confirm which route applies.
| Temperament | Zugfestigkeit (MPa) | Streckgrenze (MPa) | Dehnung | Scherfestigkeit (MPa) |
|---|---|---|---|---|
| O | 230 – 290 | 95 – 145 | 10 – 13% | 150 |
| T6 | 540 – 570 | 480 – 505 | 8 – 11% | 330 |
| T6511 | 540 – 570 | 480 – 505 | 8 – 11% | 330 |
| T73 / T73511 | 470 – 500 | 390 – 420 | 8 – 11% | 285 |
Typical AA reference figures; confirm against the MTC. Density 2.81 g/cm³, elastic modulus 71.7 GPa. The T6-to-T73 gap is roughly 70 MPa — that is what stress-corrosion resistance costs on this alloy.
T6511 is the machining default on solid square bar. A solid section removes a lot of material, and T6 carries residual stress that will bow the bar as it comes off; T6511 is stretched after quenching so it stays straight. On a key or a wear block that has to be flat, this is not a technicality.
T73 und T73511 sind absichtlich überaltert, giving up about 70 MPa for much better resistance to stress-corrosion cracking. Choose them for thick sections, sustained tensile load, or wet and salty service.
| Legierung / Zustand | Zugfestigkeit (MPa) | Streckgrenze (MPa) | Schweißeignung | Einsatzbereich |
|---|---|---|---|---|
| 7075-T6 / T6511 | 570 | 505 | Nicht schweißbar | High-load keys, wear blocks, die and tooling components |
| 2024-T351 | 462 | 324 | Nicht schweißbar | Ermüdungskritische Teile, Luftfahrtstruktur |
| 6061-T6 / T6511 | 310 | 276 | Gut | Machine parts, spacers, jigs, tapped posts |
7075 ist etwa 85% stärker als 6061 und kostet entsprechend mehr. Spezifizieren Sie 7075, wenn der Querschnitt bereits so groß wie konstruktiv möglich ist und trotzdem versagt; if a bigger 6061 bar would carry the load, it is cheaper, weldable and more corrosion-tolerant.
Massiv versus Rohr: tube gives more stiffness per kilogram, but there is no wall to hold a keyway, a thread or a clamp load. A key, a gib, a die insert or a tapped post has to be solid; a frame member should be tube.
Fertigungsweg: small and medium square bar is extruded; large squares are sawn from plate, which is why the designation changes with size on this alloy. Ask for the route to be confirmed on the quotation — it decides the corner radius, the tolerance and the certificate designation together.
On a solid square bar, check straightness before you start machining: put it on a surface plate and look for rock. A bar that has already bowed will machine to a taper no matter how the vice is set, and the cause is residual stress rather than the saw. That check takes a minute and saves a scrapped part.
Schneiden: sawn to length; 7075 saws hot, so use coolant and a sharp blade to avoid a hardened burr.
Zerspanung: excellent in T6 and T6511. Sharp carbide, climb-mill where finish matters, and order T6511 so the bar does not relieve stress as material comes off. 7075 work-hardens at the cut if the tool rubs.
Oberfläche: anodizing protects less than on 6xxx and darkens; use hard anodizing or a coating where corrosion matters, and consider T73. PVC film on plate-sawn bar protects the faces before machining.
High-load machine keys and gibs, wear blocks, die and mould components, jig and fixture blocks, competition and motorsport parts, aerospace fittings, precision spacers, defence equipment.
Every order ships with an MTC reporting alloy, temper, side and mechanical results against ASTM B221 or B211. Third-party testing is available on request at additional cost; production runs under ISO 9001, ISO 14001 and ISO 45001 certified systems.
Um in einer Runde anzubieten, senden Sie: Kantenlänge × Länge, temper (T6511 for machining, T73511 for thick or wet service), route if the size is near the extruded limit, Endbearbeitung, und die Bestimmungsadresse.
Aluminiumfabrik mit Sitz in Shenzhen, mehr als 20 Jahre Branchenerfahrung, liefert Legierungen der Serien 1000–8000 in Standardausführungen und kundenspezifischen Größen.
Q: Why T6511 rather than T6?
A: Because a solid square bar removes a lot of material when machined, and T6 carries residual stress that bows the bar. T6511 is stretched to relieve it — same strength, different stability.
Q: Can I get T651 or T7351 on square bar?
A: Only where the bar is sawn from plate, which happens at larger sizes. Give us the side and we will confirm which route and designation apply.
Q: Can 7075 square bar be welded?
A: Nein. Schmelzschweißen verursacht Heißrisse und zerstört den Zustand in der wärmebeeinflussten Zone. Konstruieren Sie für mechanische Befestigung.
F: Wann sollte ich T73511 verwenden?
A: Thick sections, sustained tensile load, or wet and salty service — wherever stress-corrosion cracking is a real risk. It gives up about 70 MPa for that resistance.
F: Welche Größen liefern Sie?
A: 5–200 mm side, up to 16,000 mm length, cut to size.
Linsy Vorteile
Linsy Aluminum ist ein führender Anbieter von Produkten für die Aluminiumverarbeitung und beliefert verschiedene Branchen wie die Luft- und Raumfahrt, den allgemeinen Maschinenbau, die Automobilindustrie, die Schifffahrt, den Schiffbau und andere spezialisierte industrielle Anwendungen.
Wir verpflichten uns, die höchsten Qualitäts- und Umweltstandards einzuhalten, was durch unsere Zertifizierungen belegt wird: ISO 9001:2008, ISO 14001:2004 und SGS.